AUTOMATIC TRANSAXLE SYSTEM > Transmission Control Switch Circuit |

| 1.READ VALUE USING GTS (SPORT SHIFT SWITCH STATUS) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Sport Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sport Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Result | Proceed to |
| Data List values are not normal | A |
| Data List values are normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH) |
Disconnect the I44 transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| l44-4 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| l44-2 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.INSPECT LOWER SHIFT LEVER ASSEMBLY (TRANSMISSION CONTROL SWITCH) |
![]() |
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected (Transmission Control Switch (Lower Shift Lever Assembly)) |
| Tester Connection | Condition | Specified Condition |
| 4 (IG) - 5 (S) | Shift lever in S, "+" or "-" | Below 1 Ω |
| Shift lever not in S, "+" or "-" | 10 kΩ or higher | |
| 3 (SFTU) - 2 (E) | Shift lever held in "+" (Up shift) | Below 1 Ω |
| Shift lever not held in "+" | 10 kΩ or higher | |
| 1 (SFTD) - 2 (E) | Shift lever held in "-" (Down shift) | Below 1 Ω |
| Shift lever not held in "-" | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) |
Connect the I44 transmission control switch connector.
Disconnect the A84 ECM connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A84-59 (S) - Body ground |
| 11 to 14 V |
| A84-59 (S) - Body ground |
| Below 1 V |
Turn the engine switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A84-42 (SFTU) - Body ground | Shift lever held in "+" (Up shift) | Below 1 Ω |
| Shift lever not held in "+" | 10 kΩ or higher | |
| A84-43 (SFTD) - Body ground | Shift lever held in "-" (Down shift) | Below 1 Ω |
| Shift lever not held in "-" | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||