Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

DTC    B2282    Vehicle Speed Signal Malfunction

DTC    B2283    Vehicle Speed Sensor Malfunction

for Preparation Click here


DESCRIPTION

DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.
DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.

HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2282
The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match.
  1. AM2 fuse
  2. Meter/gauge system
  3. Certification ECU (smart key ECU assembly)
  4. Junction Connector
  5. Wire harness or connector
Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds.
B2283
Either of the of the following malfunctions is detected (a vehicle speed sensor malfunction is detected) (1-trip detection logic*)
  1. Vehicle speed signal malfunction detection 1: Excessive deceleration is detected
  2. Vehicle speed signal malfunction detection 2: Engine speed linked detection
  1. AM2 fuse
  2. Meter/gauge system
  3. Certification ECU (smart key ECU assembly)
  4. Junction Connector
  5. Wire harness or connector
Run the engine at an engine speed of 2000 rpm or more for 330 seconds.
  1. *: Only detected while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected 
DTC Code
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
B2282
  1. When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.
  2. When the signal from the direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the engine switch cannot be turned from on (IG) to off.
-
B2283
  1. The power source mode is changed to off (the engine is stopped) by pressing the engine switch while the vehicle is being driven.
  2. With the electrical key transmitter in the cabin, even if an engine start operation is performed, the engine does not start.
-

WIRING DIAGRAM


for 2GR-FE

B387357E02


for 2AR-FE

B387358E06


for 6AR-FSE

B407407E01

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.
  2. If a short occurs in an ECU, all systems in the diagram above will not operate normally.


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry & Start / DTC.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Start Function) precaution (Click here).
  4. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  5. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


HINT:

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2282
B2283
Power Source Control
  1. Vehicle Speed Signal
  2. Engine Condition
  3. Power Supply Condition
Starting Control
  1. Engine Speed
Combination Meter
  1. Vehicle Speed Meter
-

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Check the Data List for proper functioning of the vehicle speed signal.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost same as actual vehicle speed (Speedometer tester)
    -

    OK:
    Vehicle speed displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
GO TO METER / GAUGE SYSTEM (Speedometer Malfunction) (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER
  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle speed signal
    Vehicle being driven or stopped/Stop or Run
    Stop: Vehicle stopped
    Run: Vehicle being driven at 5 km/h (3 mph) or more
    -

    OK:
    Stop (vehicle is stopped) and Run (vehicle is running) appear on the screen.



NG
Go to step 3
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B268625E07
  1. Disconnect the A43 connector from the certification ECU (smart key ECU assembly).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A43-2 (+B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (smart key ECU assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


4.CHECK HARNESS AND CONNECTOR (GROUND)
B268625E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A43-11 (E) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Certification ECU (smart key ECU assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
  1. Disconnect the I78 connector from the certification ECU (smart key ECU assembly).

  1. Disconnect the I18 connector from the combination meter assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I78-27 (SPD) - I18-3 (+S)
    Always
    Below 1 Ω
    I78-27 (SPD) or I18-3 (+S) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 7
OK


6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Reconnect the I78 certification ECU (smart key ECU assembly) connector.


    B274541E03


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    -
    -

  1. Reconnect the A43 combination meter assembly connector.

  1. Connect an oscilloscope to terminal I78-27 (SPD) and A43-11 (E).

  1. Turn the engine switch on (IG).

  1. Check the signal waveform according to the condition(s) in the table below.
    Item
    Condition
    Tester Connection
    I78-27 (SPD) - A43-11 (E)
    Tool setting
    5 V/DIV., 20 ms./DIV.
    Vehicle condition
    Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

    OK:
    The waveform is similar to that shown in the illustration.

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.



NG
GO TO METER / GAUGE SYSTEM (Speed Signal Circuit) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR)
  1. Disconnect the I124 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-3 (+S) - I124-18
    Always
    Below 1 Ω
    I18-3 (+S) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - JUNCTION CONNECTOR)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I78-27 (SPD) - I124-21
    Always
    Below 1 Ω
    I78-27 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE JUNCTION CONNECTOR