DTC B2282 Vehicle Speed Signal Malfunction |
DTC B2283 Vehicle Speed Sensor Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B2282 | The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication (1-trip detection logic*) do not match. |
| Drive the vehicle for 20 seconds at a vehicle speed of 25 km/h (16 mph) or more, and then drive the vehicle at a vehicle speed of less than 5 km/h (3 mph) for 20 seconds. |
| B2283 | Either of the of the following malfunctions is detected (a vehicle speed sensor malfunction is detected) (1-trip detection logic*)
|
| Run the engine at an engine speed of 2000 rpm or more for 330 seconds. |
| DTC Code | Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
| B2282 |
| - |
| B2283 |
| - |

| DTC | Data List Item | Active Test Item |
| B2282 B2283 | Power Source Control
Starting Control
Combination Meter
| - |
| 1.READ VALUE USING GTS |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Check the Data List for proper functioning of the vehicle speed signal.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed Meter | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost same as actual vehicle speed (Speedometer tester) | - |
|
| ||||
| OK | |
| 2.READ VALUE USING GTS |
Enter the following menus: Body Electrical / Power Source Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle speed signal | Vehicle being driven or stopped/Stop or Run | Stop: Vehicle stopped Run: Vehicle being driven at 5 km/h (3 mph) or more | - |
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (POWER SOURCE) |
![]() |
Disconnect the A43 connector from the certification ECU (smart key ECU assembly).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A43-2 (+B) - Body ground | Always | 11 to 14 V |
| *a | Rear view of wire harness connector (to Certification ECU (smart key ECU assembly)) |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A43-11 (E) - Body ground | Always | Below 1 Ω |
| *a | Rear view of wire harness connector (to Certification ECU (smart key ECU assembly)) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY) |
Disconnect the I78 connector from the certification ECU (smart key ECU assembly).
Disconnect the I18 connector from the combination meter assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I78-27 (SPD) - I18-3 (+S) | Always | Below 1 Ω |
| I78-27 (SPD) or I18-3 (+S) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Reconnect the I78 certification ECU (smart key ECU assembly) connector.

| *a | Component with harness connected (Certification ECU (Smart Key ECU Assembly)) | - | - |
Reconnect the A43 combination meter assembly connector.
Connect an oscilloscope to terminal I78-27 (SPD) and A43-11 (E).
Turn the engine switch on (IG).
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
| Tester Connection | I78-27 (SPD) - A43-11 (E) |
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - JUNCTION CONNECTOR) |
Disconnect the I124 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-3 (+S) - I124-18 | Always | Below 1 Ω |
| I18-3 (+S) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I78-27 (SPD) - I124-21 | Always | Below 1 Ω |
| I78-27 (SPD) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||