TIRE PRESSURE WARNING SYSTEM > REGISTRATION |
| 1. BEFORE REGISTRATION |
In case of tire pressure warning ECU and receiver replacement:
Read the registered transmitter IDs that are stored in the old ECU using the GTS and write them down.
If reading the stored transmitter IDs is impossible due to malfunctions of components such as the tire pressure warning ECU and receiver, remove the tires from the wheels and check the IDs located on the tire pressure warning valve and transmitters.
In case of tire pressure warning valve and transmitter replacement:
Take a note of the 7-digit number (transmitter ID) written on the tire pressure warning valve and transmitter.

| *1 | Tire Pressure Warning Valve and Transmitter | *2 | Transmitter ID (7-digit Number) |
| 2. REGISTER TRANSMITTER ID (USING GTS) |
Set the tire pressure to the specified value (Click here).
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Utility / ID Registration.
Perform the procedure displayed on the GTS.
| 3. CONFIRMATION OF TRANSMITTER ID REGISTRATION |
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure/ min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If N/A is displayed, data has not been received.*1 |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure/ min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If N/A is displayed, data has not been received.*1 |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure/ min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If N/A is displayed, data has not been received.*1 |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure/ min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If N/A is displayed, data has not been received.*1 |
| ID 5 Tire Inflation Pressure | ID5 tire inflation pressure/ min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) | Actual tire inflation pressure | If N/A is displayed, data has not been received.*1 |
Reduce the tire inflation pressure of each tire 40 kPa (0.4 kgf/cm2, 5.8 psi) or more, and check that the "ID Tire Inflation Pressure" data is updated and that the actual tire inflation pressures are displayed.
After confirming that all of the tire inflation pressure values (except the compact spare tire) have been updated, adjust the tire inflation pressure to the specified value, press the tire pressure warning reset switch and perform initialization.