Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > Driver Side Door Entry Lock Function does not Operate

for Preparation Click here


DESCRIPTION

If the entry lock function does not operate for the driver door only, but the entry unlock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the front door outside handle assembly (for driver door) (lock sensor) (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [lock sensor]).

WIRING DIAGRAM


B281953E07


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitter sub-assembles in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
  6. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (LOCK SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry & Start or Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.


Entry & Start 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D-Door Trigger Switch
Driver door touch sensor (lock sensor) / ON or OFF
ON: Driver door touch sensor (lock sensor) touched
OFF: Driver door touch sensor (lock sensor) not touched
  1. Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).
  2. Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.

OK:
The intelligent tester display changes correctly in response to the operation of the front door outside handle assembly (for driver door).



NG
Go to step 3
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
  1. Disconnect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.

  1. Disconnect the I78 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    1. *1: for LHD
    2. *2: for RHD

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    W1-1 (TRG+) - I78-20 (TSW1)
    Always
    Below 1 Ω
    A43-11 (E) - Body ground
    Always
    Below 1 Ω
    W1-1 (TRG+) or I78-20 (TSW1) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    V1-1 (TRG+) - I78-20 (TSW1)
    Always
    Below 1 Ω
    A43-11 (E) - Body ground
    Always
    Below 1 Ω
    V1-1 (TRG+) or I78-20 (TSW1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (DRIVER DOOR LOCK SENSOR SIGNAL INPUT)


  1. Connect the W1*1 or V1*2 front door outside handle assembly (for driver door) connector.


    B274842E07


    Text in Illustration 
    *1
    Waveform
    -
    -
    *a
    Component with harness connected
    (Certification ECU (smart key ECU assembly))
    *b
    In actuality, sampling is being performed
    1. *1: for LHD
    2. *2: for RHD

  1. Connect the I78 certification ECU (smart key ECU assembly) connector.

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    I78-20 (TSW1) - A43-11 (E)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Driver door lock sensor not touched → touched
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform)

Result:
Result
Proceed to
OK
A
NG (for TMMK Made)
B
NG (for TMC, TMMR Made)
C



B
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (Click here)

C
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER DOOR) (Click here)
A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)