Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR (for TMMK Made)

FRONT DOOR (for TMMK Made) > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B380633
  1. Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel plug as shown in the illustration.



4. REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER


    B380639
  1. Disengage the 2 claws and 2 guides to remove the front door front lower frame upper cover.



5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    B380635
  1. Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides.

  1. Disconnect each connector to remove the power window regulator master switch assembly with front door armrest base panel.



6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    B401212
  1. Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides.

  1. Disconnect each connector to remove the power window regulator switch assembly with front door armrest base panel.



7. REMOVE FRONT ARMREST ASSEMBLY


    B277187
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides to remove the front armrest assembly.



8. REMOVE COURTESY LIGHT ASSEMBLY


    E226714E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side
    *1
    Protective Tape

  1. Disconnect the connector and remove the courtesy light assembly.



9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B380640E01
  1. Apply protective tape to the front door panel.
    Text in Illustration 
    *a
    Protective Tape



    B380641
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 10 clips.



    B380642E01
  1. Pull out the front door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Front Door Inner Glass Weatherstrip
    *a
    Reference Boss

  1. Disengage the reference boss from the front door panel.

  1. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.



    B380644
  1. Disengage the clamp.

  1. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly as shown in the illustration.



10. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B380646
  1. Disengage the 2 claws and guide to remove the front door inside handle sub-assembly.



11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    B380647E01
  1. Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver



12. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    B380648
  1. Disengage the 3 clips to remove the front door lower frame bracket garnish.



13. REMOVE DOOR SIDE AIRBAG SENSOR
  1. Check that the engine switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



  1. Disconnect the connector from the door side airbag sensor.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.




    1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)


      H043302E12


      Text in Illustration 
      *1
      White Housing Lock
      *2
      Yellow CPA
      *a
      Connector Lock is Released
      -
      -

    2. Push down the white housing lock again and disconnect the connector.

      NOTICE:
      Do not push down the part (A) shown in the illustration when disconnecting.



    B278819
  1. Remove the bolt and door side airbag sensor from the front door panel.

    NOTICE:
    Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.



  1. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.


    B296255E01


    Text in Illustration 
    *a
    Incorrect
    *b
    Correct



14. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

NOTICE:
Do not touch the speaker cone.



    E226775
  1. Disconnect the connector.

  1. Remove the 4 screws.



    E226773
  1. Disengage the 2 claws and remove the front No. 1 speaker assembly.



15. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY


    B381033
  1. Remove the clip.



    B381034
  1. Disconnect the connector.

  1. Remove the 3 bolts.

  1. Disengage the claw.



    B381035
  1. Disengage the clip to remove the outer rear view mirror assembly.



16. REMOVE FRONT DOOR SERVICE HOLE COVER


    B380649
  1. Remove the bolt.

  1. Disconnect each connector.

  1. Disengage the 5 clamps.

  1. Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through the front door service hole cover.

  1. Remove the front door service hole cover.

    HINT:
    Remove any remaining butyl tape from the front door panel.



17. REMOVE NO. 1 FRONT DOOR SERVICE HOLE SEAL


    B380652
  1. Remove the No. 1 front door service hole seal.



18. REMOVE NO. 2 FRONT DOOR SERVICE HOLE SEAL


    B380653
  1. Remove the No. 2 front door service hole seal.



19. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    B277200
  1. Remove the grommet.

  1. Connect the cable to the negative (-) battery terminal.

  1. for Driver Side:

    1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    2. Disconnect the power window regulator master switch assembly.

  1. for Front Passenger Side:

    1. Connect the power window regulator switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    2. Disconnect the power window regulator switch assembly.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



    B280340
  1. Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the front door glass sub-assembly to fall.



    B280342E02
  1. Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

    NOTICE:
    Do not damage the front door glass sub-assembly.



20. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    B280343E03
  1. Loosen the temporary bolt.
    Text in Illustration 
    *a
    Temporary Bolt

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.

  1. Remove the 5 bolts.

  1. Remove the front door window regulator assembly.

  1. Remove the temporary bolt from the front door window regulator assembly.



21. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B380654
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.



22. REMOVE NO. 2 FRONT DOOR STIFFENER CUSHION


    B388122E01
  1. Remove the 2 bolts.
    Text in Illustration 
    *a
    Double-sided Tape

  1. Disengage the 2 guides and remove the No. 2 front door stiffener cushion.



23. REMOVE FRONT DOOR GLASS RUN


    B280345
  1. Remove the front door glass run.



24. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    B280347
  1. Remove the 2 bolts.

  1. Disengage the guide and remove the front door front lower frame sub-assembly as shown in the illustration.



25. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B280349
  1. Remove the 2 bolts.

  1. Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.



26. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    B280351
  1. Remove the hole plug.



    B280352
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



27. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    B280353
  1. Using a screwdriver, disengage the claw and 2 guides, and remove the front door outside handle cover from the lock cylinder assembly as shown in the illustration.



28. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    B280630
  1. Remove the hole plug.



    B280355
  1. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



29. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B280356
  1. Disengage the 2 claws.

  1. Using a screwdriver, disconnect the connector.



    B280357
  1. Remove the front door outside handle assembly as shown in the illustration.



30. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD


    B280359
  1. Disengage the 3 claws to remove the front door front outside handle pad.



31. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD


    B280360
  1. Disengage the 2 claws to remove the front door rear outside handle pad.



32. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY


    B280361E01
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

  1. Slide the front door lock with motor assembly downward to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.



  1. When reusing the front door lock with motor assembly:



      B280363
    1. Remove the door lock wiring harness seal from the front door lock with motor assembly.



33. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B280364
  1. Remove the front door lock remote control cable assembly as shown in the illustration.



34. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280366
  1. Using a screwdriver, disengage the 3 claws.



    B280367
  1. Remove the front door inside locking cable assembly as shown in the illustration.



35. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B280369
  1. Disconnect the connector.

  1. Disengage the 3 clamps.



    B402365E01
  1. Using a T30 "TORX" socket wrench, remove the screw and door handle nut.
    Text in Illustration 
    *A
    Outside
    *B
    Inside
    *1
    Door Handle Nut

  1. Slide the front door outside handle frame sub-assembly to disengage the claw of the front door outside handle frame sub-assembly, and then remove it.



36. REMOVE FRONT DOOR WIRE


    B280372
  1. Disengage the 3 clamps and remove the front door wire.



37. REMOVE FRONT DOOR LOCK OPEN ROD


    B280374E02
  1. Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.



38. REMOVE FRONT DOOR CHECK ASSEMBLY


    B280375
  1. Remove the 3 bolts and front door check assembly.



39. REMOVE FRONT DOOR WEATHERSTRIP


    B280376
  1. Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.



40. REMOVE DOOR FRAME GARNISH


    B277197
  1. Disengage the clip and remove the door frame garnish.

    HINT:
    This garnish needs to be replaced with a new one because the clip will break when removing it.



41. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP


    B280377
  1. Using a clip remover, disengage the 8 clips and remove the front door No. 2 weatherstrip.



42. REMOVE FRONT DOOR PANEL CUSHION


    B280378
  1. Disengage the 2 claws and remove the 2 front door panel cushions.



43. REMOVE DOOR DUST PROOF SEAL


    B380655E01
  1. Remove the 2 door dust proof seals.
    Text in Illustration 
    *A
    for Front Side
    *B
    for Rear Side



44. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY


    B380981
  1. Apply protective tape around the front door belt moulding assembly as shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B380982E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 5 claws as shown in the illustration and remove the front door belt moulding assembly.
    Text in Illustration 
    *a
    Screwdriver
    V100155
    Protective Tape



45. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

HINT:
When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Front Door Rear Window Frame Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or front door rear window frame moulding excessively.

  1. Using a heat light, heat the front door rear window frame moulding.



    B381015E01
  1. Using a moulding remover, disengage the clip and guide, and separate the double-sided tape to remove the front door rear window frame moulding.
    Text in Illustration 
    *a
    Caulking Sponge
    V100155
    Double-sided Tape



46. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
  1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.



    B381017E01
  1. Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

    Standard Measurement:
    Area
    Measurement
    A
    5.0 mm (0.197 in.)

    NOTICE:
    Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 7 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Prying the rivets with the drill may damage the rivet installation holes or drill bit.
    3. Be careful of the drilled rivets, as they may be hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Disengage the claw and guide, and remove the front door upper window frame moulding from the door frame.



47. REMOVE FRONT DOOR STRIPE
  1. Using a heat light, heat the front door stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Front Door Outside Stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B280089
  1. Pull back on one of the ends of the front door stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



48. REMOVE FRONT DOOR LOWER OUTSIDE STRIPE
  1. Using a heat light, heat the front door lower outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Front Door Rear Outside Stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B280090
  1. Pull back on one of the ends of the front door lower outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.