Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment

for Preparation Click here


DESCRIPTION

If the luggage compartment door entry unlock function does not operate, the request code may not be being transmitted from the luggage compartment door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage)), a luggage compartment door outer switch malfunction or wave interference.

HINT:
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.


WIRING DIAGRAM


B274856E19


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
  6. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

1.READ VALUE USING INTELLIGENT TESTER (LUGGAGE COMPARTMENT DOOR OPEN MODE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry & Start / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Trunk Open Mode
    Luggage door opening switch assembly / ON or OFF
    Customization status displayed
    -

    Result:
    Result
    Proceed to
    Entry luggage compartment door open mode is ON
    A
    Entry luggage compartment door open mode is OFF
    B



B
PERFORM CUSTOMIZE SETTING (Proceed to Customize Parameters) (Click here)
A


2.READ VALUE USING INTELLIGENT TESTER (LUGGAGE DOOR OPENING SWITCH ASSEMBLY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Entry & Start / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Entry & Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tr/B-Door Unlock SW
    Luggage compartment door opener outer switch / ON or OFF
    ON: Luggage compartment door opener outer switch pushed
    OFF: Luggage compartment door opener outer switch not pushed
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF according to the chart above.



NG
Go to step 8
OK


3.PERFORM ACTIVE TEST USING ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Trunk and Back-door Open
    Operate luggage compartment door lock motor
    ON/OFF
    -

    OK:
    Luggage compartment door lock motor operates.



NG
Go to step 10
OK


4.CHECK WAVE ENVIRONMENT


    B364804E01
  1. Bring the electrical key transmitter sub-assembly near the electrical key antenna (outside luggage), and perform an entry luggage compartment open function check.
    Text in Illustration 
    *A
    for Type A
    *B
    for Type B
    *a
    Approximately 0.3 m (0.984 ft.)

    NOTICE:
    If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication is not possible.

    HINT:
    1. When pressing the luggage compartment door opener outer switch, hold the electrical key transmitter sub-assembly approximately 1 m (3.28 ft.) above the ground and approximately 0.3 m (0.984 ft.) away from the vehicle as shown in the illustration.
    2. When the electrical key transmitter sub-assembly is brought near the electrical key antenna (outside luggage), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    3. If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Entry functions operate normally.



NG
Go to step 5
OK

AFFECTED BY WAVE INTERFERENCE 

5.CHECK KEY DIAGNOSTIC MODE
  1. Check the following antennas in the key diagnostic mode (Click here).



    B364804E01
  1. Select either channel 1 or channel 2 and inspect the key diagnostic mode for each channel.
    Text in Illustration 
    *A
    for Type A
    *B
    for Type B
    *a
    0.7 to 1.0 m (2.30 to 3.28 ft.)

    1. When the electrical key transmitter sub-assembly is held at the same height as the rear bumper upper surface, align it with the center of the rear of the vehicle and check that the wireless door lock buzzer sounds.

      HINT:
      1. Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle (0.7 to 1.0 m (2.30 to 3.28 ft.)). Make sure that the direction of the electrical key transmitter sub-assembly is as shown in the illustration.
      2. If the buzzer sounds, it can be determined that the luggage compartment exterior transmitter is operating normally.
      3. If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.

      OK:
      Wireless door lock buzzer sounds.



NG
Go to step 6
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ELECTRICAL KEY ANTENNA)
  1. Disconnect the O1 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the T11 electrical key antenna (outside luggage) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    except TMMK Made 
    Tester Connection
    Condition
    Specified Condition
    O1-1 (CG8B) - T11-2 (CLGB)
    Always
    Below 1 Ω
    O1-2 (CLG8) - T11-1 (CLG5)
    Always
    Below 1 Ω
    O1-1 (CG8B) or T11-2 (CLGB) - Body ground
    Always
    10 kΩ or higher
    O1-2 (CLG8) or T11-1 (CLG5) - Body ground
    Always
    10 kΩ or higher
    for TMMK Made 
    Tester Connection
    Condition
    Specified Condition
    O1-1 (CG8B) - T11-2 (CLGB)
    Always
    Below 1 Ω
    O1-2 (CLG8) - T11-1 (ANTE8)
    Always
    Below 1 Ω
    O1-1 (CG8B) or T11-2 (CLGB) - Body ground
    Always
    10 kΩ or higher
    O1-2 (CLG8) or T11-1 (ANTE8) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
  1. Remove the outside electrical key antenna (outside luggage) (Click here).

  1. Inspect the outside electrical key antenna (outside luggage) (Click here).



NG
REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) (Click here)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

8.INSPECT LUGGAGE DOOR OPENING SWITCH ASSEMBLY
  1. Remove the luggage door opening switch assembly (Click here).



    B142645E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    2 (E) - 3 (UL)
    Luggage door opening switch assembly not pushed
    10 kΩ or higher
    2 (E) - 3 (UL)
    Luggage door opening switch assembly pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Luggage Door Opening Switch Assembly)



NG
REPLACE LUGGAGE DOOR OPENING SWITCH ASSEMBLY (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - OPENING SWITCH)
  1. Disconnect the O1 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the T4 luggage door opening switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O1-27 (TSW5) - T4-3 (UL)
    Always
    Below 1 Ω
    O1-27 (TSW5) or T4-3 (UL) - Body ground
    Always
    10 kΩ or higher
    T4-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) 

10.INSPECT LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY


    B279065E03
  1. Remove the luggage compartment door lock assembly (Click here).

  1. Check the operation of the door lock motor.

    1. Move the door lock to the close (lock) position.

    2. Apply battery voltage to the door lock motor and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1 (B)
      Battery negative (-) → 2 (E)
      Luggage compartment door lock motor open (unlock) operation

      Text in Illustration 
      *a
      Component without harness connected:
      (Luggage Compartment Door Lock Assembly)
      *b
      Close (Lock)
      *c
      Open (Unlock)



    B279065E01
  1. Check the door courtesy light switch.

    1. Move the door lock to the close (lock) position.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Measurement Condition
      Door Lock Condition
      Specified Condition
      2 (E) - 3 (D+)
      Close (Lock)
      10 kΩ or higher
      2 (E) - 3 (D+)
      Open (Unlock)
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Luggage Compartment Door Lock Assembly)
      *b
      Close (Lock)
      *c
      Open (Unlock)



NG
REPLACE LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (LUGGAGE DOOR LOCK - INSTRUMENT PANEL JUNCTION BLOCK)
  1. Luggage compartment door lock motor:

    1. Disconnect the 3C instrument panel junction block assembly connector.

    2. Disconnect the T3 luggage compartment door lock assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      T3-2 (E) - Body ground
      Always
      Below 1 Ω
      3C-10 (TR+) or T3-1 (B) - Body ground
      Always
      10 kΩ or higher
      3C-10 (TR+) - T3-1 (B)
      Always
      Below 1 Ω

  1. Luggage door courtesy light switch:

    1. Disconnect the 3C instrument panel junction block assembly connector.

    2. Disconnect the T3 luggage compartment door lock assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      T3-2 (E) - Body ground
      Always
      Below 1 Ω
      3C-9 (LGCY) or T3-3 (D+) - Body ground
      Always
      10 kΩ or higher
      3C-9 (LGCY) - T3-3 (D+)
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Temporarily replace the instrument panel junction block assembly with a new one (Click here).


NEXT


13.CHECK OPERATION
  1. Check that the luggage compartment door entry unlock functions operate normally (Click here).

OK:
Luggage compartment door entry unlock functions operate normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WAS DEFECTIVE)