Home › Steering › STEERING COLUMN › POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

DTC    B2611    Telescopic Position Sensor or Telescopic Motor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The telescopic motor is operated by voltage supplied from the multiplex tilt and telescopic ECU and slides the steering column forward and backward. The telescopic position sensor (Hall IC) in the telescopic motor detects the sliding position of the steering column in the forward and backward directions and sends a signal to the multiplex tilt and telescopic ECU based on that sliding amount.

C152160E02


HINT:
Limit positions can be confirmed on the intelligent tester.

DTC No.
Detection Item
Trouble Area
B2611
Telescopic operation stops within the operation range while operating.
  1. Telescopic position sensor or telescopic motor
  2. Harness or connector
  3. Multiplex tilt and telescopic ECU


WIRING DIAGRAM


C244373E02


INSPECTION PROCEDURE

NOTICE:
If the electric power steering column sub-assembly has been replaced with a new one, perform torque sensor zero point calibration after performing the initialization of the torque sensor zero point value (Click here).

HINT:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. The wire harness between the multiplex tilt and telescopic ECU and telescopic motor is provided with the electric power steering column sub-assembly.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TELESCO OPERATION)


    C106469E02
  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Check that the steering column contracts and extends. Enter the following menus: Body / Tilt & Telescopic / Active Test.

    Tilt & Telescopic 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Telesco Operation
    Telescopic operation
    LONG/SHORT
    -

    OK:
    The steering column contracts and extends.

Text in Illustration 
*a
Extend
*b
Contract


NG
Go to step 6
OK


2.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)


    C240239E15
  1. Disconnect the I15 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I15-2 (+B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)


    C240239E14
  1. Disconnect the I15 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I15-1 (GND) - Body ground
    Always
    Below 1 Ω
    I15-8 (GND2) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC MOTOR)
  1. Disconnect the I15 multiplex tilt and telescopic ECU connector.

  1. Disconnect the I14 telescopic motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I15-6 (TEM+) - I14-2 (TEM+)
    Always
    Below 1 Ω
    I15-19 (TEM-) - I14-1 (TEM-)
    I15-6 (TEM+) - Body ground
    10 kΩ or higher
    I15-19 (TEM-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK TELESCOPIC MOTOR


    C197978E09
  1. Apply 12 V battery voltage to the telescopic motor connector. Then check the steering column telescopic operation.

    OK:
    Measurement Condition
    Specified Condition
    1. 12 V battery positive (+) lead → Terminal 2 (TEM+)
    2. 12 V battery negative (-) lead → Terminal 1 (TEM-)
    The steering column contracts.
    1. 12 V battery positive (+) lead → Terminal 1 (TEM-)
    2. 12 V battery negative (-) lead → Terminal 2 (TEM+)
    The steering column extends.

Text in Illustration 
*a
Component without harness connected
(Telescopic Motor)


NG
REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)  

6.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TELESCOPIC POSITION SENSOR)
  1. Disconnect the I15 multiplex tilt and telescopic ECU connector.

  1. Disconnect the I14 telescopic motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I15-14 (VCE) - I14-4 (VCE)
    Always
    Below 1 Ω
    I15-15 (TES) - I14-5 (TES)
    I15-17 (E2) - I14-6 (E2)
    I15-14 (VCE) - Body ground
    10 kΩ or higher
    I15-15 (TES) - Body ground
    I15-17 (E2) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)


    C240239E14
  1. Disconnect the I15 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I15-1 (GND) - Body ground
    Always
    Below 1 Ω
    I15-8 (GND2) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCE, TES TERMINAL VOLTAGE)


    C240240E10
  1. Disconnect the I14 telescopic motor connector.

  1. Reconnect the I15 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I15-14 (VCE) - I15-17 (E2)
    Engine switch on (IG)
    8 to 16 V
    I15-15 (TES) - I15-17 (E2)

Text in Illustration 
*a
Component with harness connected
(Multiplex Tilt and Telescopic ECU)


NG
REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)
OK


9.CHECK TELESCOPIC POSITION SENSOR


    C240240E11
  1. Reconnect the I15 multiplex tilt and telescopic ECU connector.

  1. Reconnect the I14 telescopic motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I15-15 (TES) - I15-17 (E2)
    Steering column contracting or extending
    Pulse generation
    High: 8 to 16 V
    Low: Below 1 V

Text in Illustration 
*a
Component with harness connected
(Multiplex Tilt and Telescopic ECU)


NG
REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY (Click here)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)