HOOD LOCK CONTROL CABLE ASSEMBLY (for TMC, TMMR Made) > REMOVAL |
| 1. REMOVE FRONT BUMPER ASSEMBLY |
| 2. REMOVE FRONT WHEEL LH (for LHD) |
| 3. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for LHD) |
| 4. REMOVE FRONT FENDER LINER LH (for LHD) |
| 5. REMOVE FRONT WHEEL RH (for RHD) |
| 6. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for RHD) |
for TMC, TMMR Made:
![]() |
Remove the 3 screws and front wheel opening extension pad RH.
for TMMK Made:
![]() |
Remove the 3 screws and front wheel opening extension pad RH.
| 7. REMOVE FRONT FENDER LINER RH (for RHD) |
for TMC, TMMR Made:
![]() |
Remove the clip.
![]() |
Using a screwdriver, turn the pin 90 degrees counterclockwise and remove the pin hold clip.
| *a | 90° |
![]() |
Remove the 5 screws.
| *1 | Grommet |
Remove the 4 clips, 2 grommets and front fender liner RH.
for TMMK Made:
![]() |
Remove the clip.
![]() |
Using a screwdriver, turn the pin 90 degrees counterclockwise and remove the pin hold clip.
| *a | 90° |
![]() |
Remove the 5 screws and bolt.
| *1 | Grommet |
Remove the 4 clips, 3 grommets and front fender liner RH.
| 8. REMOVE FRONT DOOR SCUFF PLATE LH (for LHD) |
![]() |
Disengage the 10 claws and remove the front door scuff plate LH.
| 9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for LHD) |
![]() |
Remove the clip.
Disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 10. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD) |
| 11. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH (for RHD) |
| 12. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
| 13. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock control lever sub-assembly.
| 14. REMOVE HOOD LOCK ASSEMBLY (for LHD) |
![]() |
Using a screwdriver, remove the hood lock nut cap.
| *1 | Protective Tape |
![]() |
Disconnect the connector.
![]() |
Remove the 2 bolts and hood lock bolt.
| *1 | Hood Lock Bolt |
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock assembly.
| 15. REMOVE HOOD LOCK ASSEMBLY (for RHD) |
![]() |
Using a screwdriver, remove the hood lock nut cap.
| *1 | Protective Tape |
![]() |
Disconnect the connector.
![]() |
Remove the 2 bolts and hood lock bolt.
| *1 | Hood Lock Bolt |
![]() |
Disconnect the hood lock control cable assembly and remove the hood lock assembly.
| 16. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD) |
Using a screwdriver, disengage the 5 clamps and hood cable grommet as shown in the illustration.

| *1 | Hood Lock Control Cable | *2 | Hood Cable Grommet |
| *3 | Washer Hose | *4 | Hood Lock Control Cable Clamp |
Pull the hood lock control cable assembly from the engine compartment and remove it.
| 17. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD) |
Using a screwdriver, disengage the 4 clamps and hood cable grommet as shown in the illustration.

| *1 | Hood Lock Control Cable | *2 | Hood Cable Grommet |
| *3 | Washer Hose | *4 | Hood Lock Control Cable Clamp |
Pull the hood lock control cable assembly from the engine compartment and remove it.