AIRBAG SYSTEM (for TMMK Made) > SRS Warning Light Remains ON |

| 1.CHECK SRS WARNING LIGHT OPERATION |
Turn the engine switch on (IG) and check the SRS warning light condition.
| Result | Proceed to |
| After the primary check period, the SRS warning light remains on. | A |
| After the primary check period, the SRS warning light goes off and comes on again. | B |
|
| ||||
| A | |
| 2.CHECK BATTERY VOLTAGE |
Measure the voltage of the battery.
|
| ||||
| OK | |
| 3.CHECK CONNECTOR |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connector is properly connected to the airbag sensor assembly.
Disconnect the connector from the airbag sensor assembly.
Check that the terminal of the connector is not damaged.
|
| ||||
| OK | |
| 4.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I47-21 (IG2) - Body ground | Engine switch on (IG) | 8 to 16 V |
Turn the engine switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I47-25 (E1) - Body ground | Always | Below 1 Ω |
| I47-26 (E2) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
|
| ||||
| OK | |
| 5.CHECK SRS WARNING LIGHT |
Turn the engine switch on (IG) and check the SRS warning light condition.
|
| ||||
| OK | ||
| ||
| 6.CHECK CAN COMMUNICATION SYSTEM |
Use the GTS to check if the CAN communication system is functioning normally.
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | |
| 7.CHECK BATTERY VOLTAGE |
Measure the voltage of the battery.
|
| ||||
| OK | |
| 8.CHECK CONNECTOR |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connector is properly connected to the airbag sensor assembly.
Disconnect the connector from the airbag sensor assembly.
Check that the terminal of the connector is not damaged.
|
| ||||
| OK | |
| 9.CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I47-21 (IG2) - Body ground | Engine switch on (IG) | 8 to 16 V |
Turn the engine switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I47-25 (E1) - Body ground | Always | Below 1 Ω |
| I47-26 (E2) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
|
| ||||
| OK | |
| 10.CHECK CONNECTOR |
Disconnect the cable from the negative (-) battery terminal.
Check that the connector is properly connected to the combination meter assembly.
Disconnect the connector from the combination meter assembly.
Check that the terminal of the connector is not damaged.
|
| ||||
| OK | |
| 11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-13 (IG+) - Body ground | Engine switch on (IG) | 11 to 14 V |
| I18-1 (B) - Body ground | Always | 11 to 14 V |
Turn the engine switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-20 (ES) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
|
| ||||
| OK | |
| 12.CHECK SRS WARNING LIGHT |
Disconnect the cable from the negative (-) battery terminal.
Connect the connector to the combination meter assembly.
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG) and check the SRS warning light condition.
|
| ||||
| OK | ||
| ||