COMBINATION METER > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column) |
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column) |
Disable the auto away/return function by changing the customize parameter (Click here).
Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.
Turn the ignition switch off and disconnect the cable from the negative (-) battery terminal.
| 4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for TMMK Made) |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP (for TMC, TMMR Made) |
![]() |
Disconnect the front door opening trim weatherstrip LH.
| 6. REMOVE INSTRUMENT SIDE PANEL LH (for TMMK Made) |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 7. REMOVE INSTRUMENT SIDE PANEL (for TMC, TMMR Made) |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 8. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for TMMK Made) |
![]() |
Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.
| 9. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD) |
![]() |
Disengage the 2 claws and 4 clips to remove the upper instrument panel finish panel as shown in the illustration.
w/ Smart Entry and Start System:
Disconnect the connector.
| 10. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for TMMK Made) |
![]() |
Apply protective tape to the area shown in the illustration.
![]() | Protective Tape |
![]() |
Disengage the 2 clips as shown in the illustration.
![]() |
Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.
| 11. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for TMC, TMMR Made) |
![]() |
Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.
| 12. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for TMMK Made) |
Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.
![]() |
Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.
![]() |
Disengage the 5 claws, 5 clips and 2 guides.
Disconnect each connector.
![]() |
Remove the instrument cluster finish panel assembly as shown in the illustration.
| 13. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for TMC, TMMR Made) |
for Manual Tilt and Manual Telescopic Steering Column:
Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.
![]() |
Using a moulding remover, disengage the 4 clips and 2 guides.
for LHD:
![]() |
Disengage the 3 claws, 7 clips and 4 guides.
for RHD:
![]() |
Disengage the 4 claws, 5 clips and 4 guides as shown in the illustration.
Disconnect each connector.
![]() |
Remove the instrument cluster finish panel assembly as shown in the illustration.
| 14. REMOVE COMBINATION METER ASSEMBLY |
![]() |
Remove the 4 screws.
![]() |
Disengage the wire harness clamp.
Disconnect the 2 connectors to remove the combination meter assembly.