Home › Vehicle Exterior › WINDOW / GLASS › FRONT DOOR POWER WINDOW REGULATOR MOTOR (for TMC, TMMR Made)

FRONT DOOR POWER WINDOW REGULATOR MOTOR (for TMC, TMMR Made) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for both the RH and LH sides.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor.



    B280344
  1. Using a T25 "TORX" socket wrench, install the front power window regulator motor assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



3. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator assembly.

  1. Install the temporary bolt to the front door window regulator assembly.



    B281734E02
  1. Temporarily install the front door window regulator assembly.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) battery terminal.

  1. Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the multiplex network master switch assembly.



    B288546E01
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.



    B288542
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B281733
  1. Install the grommet.



5. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the front door panel.



    B281685E01
  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
    Text in Illustration 
    *1
    Reference Point

  1. Attach the front door service hole cover according to the reference points on the front door panel.

    NOTICE:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.

  1. Engage the 4 clamps.

  1. Connect each connector.



6. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    B288547
  1. Install the front door inner glass weatherstrip.



7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B277193E01
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly

  1. w/o Memory:

    1. Connect the connector.

  1. w/ Memory:

    1. Connect the 2 connectors.



    B288553E01
  1. Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
    Text in Illustration 
    *1
    Reference Boss



    B288551
  1. Engage the 10 clips and install the front door trim board sub-assembly.

  1. Install the 3 screws.

  1. If protective tape has been applied, remove it.



8. INSTALL COURTESY LIGHT ASSEMBLY
  1. Connect the connector.



    E226715E01
  1. Engage the claw to install the courtesy light assembly.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



9. INSTALL FRONT ARMREST ASSEMBLY


    B277188
  1. Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.



10. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
  1. Connect each connector.



    B288554
  1. Engage the 4 guides, 2 clips and 5 claws, and install the multiplex network master switch assembly with front door armrest base panel.



11. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
  1. Connect the connector.



    B288555
  1. Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.



12. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    B288549
  1. Engage the 3 clips to install the front door lower frame bracket garnish.



13. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    B288540
  1. Engage the 3 claws to install the front door inside handle bezel plug.



14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



15. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


16. INSPECT POWER WINDOW OPERATION
(Click here)