REAR DOOR POWER WINDOW REGULATOR MOTOR (for TMC, TMMR Made) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.
| 4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
w/o Seat Heater System:
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
w/ Seat Heater System:
Disconnect the 2 connectors and remove the rear power window regulator switch assembly with rear door armrest base panel.
| 5. REMOVE REAR ARMREST ASSEMBLY |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.
| 6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Put protective tape around the rear door panel.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 8 clips.
![]() |
Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
| *1 | Reference Boss |
| *2 | Rear Door Inner Glass Weatherstrip |
Disengage the reference boss from the rear door panel.
Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
![]() |
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
Disconnect the connector.
![]() |
Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 8. REMOVE REAR DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connector and remove the rear door service hole cover.
| 9. DISCONNECT REAR DOOR WEATHERSTRIP |
![]() |
Disconnect the upper part of rear door weatherstrip as shown in the illustration.
| 10. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the rear door glass run.
| 11. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.
| 12. REMOVE REAR DOOR QUARTER WINDOW GLASS |
![]() |
Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
| 13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
| 14. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY |
![]() |
Disconnect the connector.
Loosen the temporary bolt.
| *1 | Temporary Bolt |
Remove the 3 bolts.
Remove the rear door window regulator assembly.
Remove the temporary bolt from the rear door window regulator assembly.
| 15. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a T25 "TORX" socket wrench, remove the 3 screws and rear power window regulator motor assembly.