Home › Vehicle Exterior › WINDOW / GLASS › REAR DOOR POWER WINDOW REGULATOR MOTOR (for TMMK Made)

REAR DOOR POWER WINDOW REGULATOR MOTOR (for TMMK Made) > REMOVAL

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B280387
  1. Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel plug as shown in the illustration.



4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B380656
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 3 guides.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



5. REMOVE REAR ARMREST ASSEMBLY


    B280391
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides to remove the rear armrest assembly.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B380658E01
  1. Apply protective tape to the rear door panel.
    Text in Illustration 
    *a
    Protective Tape



    B380659
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 8 clips.



    B380660E01
  1. Pull out the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Rear Door Inner Glass Weatherstrip
    *a
    Reference Boss

  1. Disengage the reference boss from the rear door panel.

  1. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    B380661
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.



    B280399E02
  1. Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver



7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B280398E02
  1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver



8. REMOVE REAR DOOR SERVICE HOLE COVER


    B380716
  1. Disconnect the connector.

  1. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through the rear door service hole cover.

  1. Remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the rear door panel.



9. DISCONNECT REAR DOOR WEATHERSTRIP


    B405619
  1. Disconnect the upper part of rear door weatherstrip as shown in the illustration.



10. REMOVE REAR DOOR GLASS RUN


    B380665
  1. Remove the rear door glass run.



11. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B380666
  1. Remove the 2 bolts and screw and rear door lower window frame sub-assembly.

    NOTICE:
    When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.



12. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B280410
  1. Remove the rear door quarter window glass as shown in the illustration.



13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B380667
  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the rear door glass sub-assembly.



14. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY


    B280418E03
  1. Disconnect the connector.
    Text in Illustration 
    *a
    Temporary Bolt

  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator assembly.

  1. Remove the temporary bolt from the rear door window regulator assembly.



15. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B280419
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and rear power window regulator motor assembly.