Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR (for TMMK Made)

REAR DOOR (for TMMK Made) > DISASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    B280387
  1. Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel plug as shown in the illustration.



4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    B380656
  1. Using a moulding remover, disengage the 2 clips, 5 claws and 3 guides.

  1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.



5. REMOVE REAR ARMREST ASSEMBLY


    B280391
  1. Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides to remove the rear armrest assembly.



6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B380658E01
  1. Apply protective tape to the rear door panel.
    Text in Illustration 
    *a
    Protective Tape



    B380659
  1. Remove the 3 screws.

  1. Using a clip remover, disengage the 8 clips.



    B380660E01
  1. Pull out the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *1
    Rear Door Inner Glass Weatherstrip
    *a
    Reference Boss

  1. Disengage the reference boss from the rear door panel.

  1. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.



    B380661
  1. Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.



    B280399E02
  1. Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver



7. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    B277194
  1. Disengage the 2 claws and guide to remove the rear door inside handle sub-assembly.



8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    B280398E02
  1. Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver



9. REMOVE REAR DOOR SERVICE HOLE COVER


    B380716
  1. Disconnect the connector.

  1. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through the rear door service hole cover.

  1. Remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the rear door panel.



10. REMOVE REAR DOOR CHECK ASSEMBLY


    B280406
  1. Remove the bolt and 2 nuts, and rear door check assembly.



11. REMOVE REAR DOOR WEATHERSTRIP


    B380664
  1. Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.



12. REMOVE REAR DOOR GLASS RUN


    B380665
  1. Remove the rear door glass run.



13. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B380666
  1. Remove the 2 bolts and screw and rear door lower window frame sub-assembly.

    NOTICE:
    When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.



14. REMOVE REAR DOOR QUARTER WINDOW GLASS


    B280410
  1. Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.



15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    B380667
  1. Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the rear door glass sub-assembly.



16. REMOVE REAR DOOR FRAME GARNISH


    B280403
  1. Disengage the clip and remove the rear door frame garnish.

    HINT:
    This garnish needs to be replaced with a new one because the clip will break when removing it.



17. REMOVE REAR DOOR INSIDE PANEL REINFORCE SUB-ASSEMBLY


    B280417
  1. Remove the 4 screws.

  1. Disengage the guide to remove the rear door inside panel reinforce sub-assembly.



18. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY


    B280418E03
  1. Disconnect the connector.
    Text in Illustration 
    *a
    Temporary Bolt

  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator assembly.

  1. Remove the temporary bolt from the rear door window regulator assembly.



19. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    B280419
  1. Using a T25 "TORX" socket wrench, remove the 3 screws and rear power window regulator motor assembly.



20. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY


    B372660E02
  1. Using a T30 "TORX" socket wrench, remove the 3 screws.
    Text in Illustration 
    *a
    Release Plate

  1. Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly and remove the rear door lock with motor assembly.



  1. When reusing the rear door lock with motor assembly.



      B380758
    1. Remove the door lock wiring harness seal from the rear door lock with motor assembly.



21. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B381728
  1. Using a screwdriver, disengage the claw as shown in the illustration.



    B381729
  1. Remove the rear door lock remote control cable assembly as shown in the illustration.



22. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    B280427
  1. Using a screwdriver, disengage the 3 claws as shown in the illustration.



    B280429
  1. Remove the rear door inside locking cable assembly as shown in the illustration.



23. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    B280431
  1. Using a T30 "TORX" socket wrench, loosen the screw.

    HINT:
    The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

  1. Disengage the claw and remove the rear door outside handle cover.



24. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    B380717
  1. Pull and hold the release plate of the rear door outside handle frame sub-assembly as shown in the illustration.

    NOTICE:
    The release plate may interfere with the rear door outside handle assembly and may be damaged when removing the rear door outside handle assembly, unless it is pulled and held.



    B280433
  1. Remove the rear door outside handle assembly as shown in the illustration.



25. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    B280435
  1. Disengage the 3 claws and remove the rear door front outside handle pad.



26. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    B280436
  1. Disengage the 2 claws and remove the rear door rear outside handle pad.



27. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    B402367E01
  1. Using a T30 "TORX" socket wrench, remove the screw and door handle nut.
    Text in Illustration 
    *A
    Outside
    *B
    Inside
    *1
    Door Handle Nut

  1. Slide the rear door outside handle frame sub-assembly to disengage the claw of the rear door outside handle frame sub-assembly, and then remove it.



28. REMOVE REAR DOOR NO. 2 WEATHERSTRIP


    B280439
  1. Using a clip remover, disengage the 5 clips and remove the rear door No. 2 weatherstrip.



29. REMOVE REAR DOOR PANEL CUSHION


    B280547
  1. Disengage the 2 claws and remove the 2 rear door panel cushions.



30. REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    B380984
  1. Apply protective tape around the rear door belt moulding assembly as shown in the illustration.
    Text in Illustration 
    V100155
    Protective Tape



    B380985E01
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the 6 claws to remove the rear door belt moulding assembly as shown in the illustration.
    Text in Illustration 
    *a
    Screwdriver
    V100155
    Protective Tape



31. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:
When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Rear Door Front Window Frame Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or rear door front window frame moulding excessively.

  1. Using a heat light, heat the rear door front window frame moulding.



    B381019E01
  1. Using a moulding remover, disengage the clip and guide, and separate the double-sided tape to remove the rear door front window frame moulding.
    Text in Illustration 
    *a
    Caulking Sponge
    V100155
    Double-sided Tape



32. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING
  1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.



    B381021E01
  1. Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

    Standard Measurement:
    Area
    Measurement
    A
    5.0 mm (0.197 in.)

    NOTICE:
    Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 4 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Prying the rivets with the drill may damage the rivet installation holes or drill bit.
    3. Be careful of the drilled rivets, as they may be hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Disengage the guide and remove the rear door upper window frame moulding from the door frame.



33. REMOVE REAR DOOR REAR WINDOW FRAME MOULDING
  1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.



    B381023E01
  1. Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

    Standard Measurement:
    Area
    Measurement
    A
    5.0 mm (0.197 in.)

    NOTICE:
    Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 4 rivets.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Prying the rivets with the drill may damage the rivet installation holes or drill bit.
    3. Be careful of the drilled rivets, as they may be hot.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

  1. Remove the rear door rear window frame moulding.



34. REMOVE NO. 2 BLACK OUT TAPE
  1. Using a heat light, heat the No. 2 black out tape and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and No. 2 Black Out Tape
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B381003
  1. Pull back on one of the ends of the No. 2 black out tape to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



35. REMOVE REAR DOOR OUTSIDE STRIPE
  1. Using a heat light, heat the rear door outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Rear Door Outside Stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B381004
  1. Pull back on one of the ends of the rear door outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.



36. REMOVE REAR DOOR LOWER OUTSIDE STRIPE
  1. Using a heat light, heat the rear door lower outside stripe and vehicle body.
    Heating Temperature 
    Item
    Temperature
    Vehicle Body and Rear Door Lower Outside stripe
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.



    B381005
  1. Pull back on one of the ends of the rear door lower outside stripe to remove it.

    HINT:
    When pulling on the stripe, pull it parallel to the body.