Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM

DTC    B2416    Height Control Sensor Malfunction

for Preparation Click here


DESCRIPTION

The DTC is stored when the headlight leveling ECU assembly detects malfunctions in the rear height control sensor sub-assembly power source or rear height control sensor sub-assembly.

DTC No.
DTC Detecting Condition
Trouble Area
B2416
  1. Malfunction in rear height control sensor sub-assembly
  2. Open or short in rear height control sensor sub-assembly power source circuit
  1. Rear height control sensor sub-assembly
  2. Harness or connector
  3. Headlight leveling ECU assembly

WIRING DIAGRAM


E223762E02


INSPECTION PROCEDURE

NOTICE:
If either of the following is performed, initialization of the headlight leveling ECU assembly is necessary (Click here).
  1. Replacement of the headlight leveling ECU assembly.
  2. Replacement or removal/installation of the rear height control sensor sub-assembly or work that changes the vehicle height such as replacement of suspension components.

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B2416 is not output



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / HL AutoLeveling / Data List.

  1. Read the display on the intelligent tester.

    HL AutoLeveling 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Height Sens Pw Supply Val
    Height control sensor power supply value / 0.00 to 5.00 V
    Approx. 5 V
    -

    OK:
    Normal condition listed above is displayed.



NG
Go to step 3
OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)  

3.INSPECT REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY
  1. Remove the rear height control sensor sub-assembly (for TMC, TMMR Made: Click here), (for TMMK Made: Click here).

  1. Inspect the rear height control sensor sub-assembly (for TMC, TMMR Made: Click here), (for TMMK Made: Click here).


Result:

Result
Proceed to
OK
A
NG (for TMC, TMMR Made)
B
NG (for TMMK Made)
C



B
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (Click here)

C
REPLACE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (Click here)
A


4.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY)
  1. Disconnect the A34 headlight leveling ECU assembly connector.

  1. Disconnect the O17 rear height control sensor sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A34-12 (SBR) - O17-3 (SHB)
    Always
    Below 1 Ω
    A34-19 (SHRL) - O17-2 (SHRR)
    Always
    Below 1 Ω
    A34-21 (SGR) - O17-1 (SHG)
    Always
    Below 1 Ω
    A34-12 (SBR) - Body ground
    Always
    10 kΩ or higher
    A34-19 (SHRL) - Body ground
    Always
    10 kΩ or higher
    A34-21 (SGR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY (Click here)