Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY

FRONT SEAT OUTER BELT ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    B271086E02
  1. Engage the guide.

  1. Install the bolt (A) first, then the bolt (B) to temporarily install the front shoulder belt anchor adjuster assembly.

  1. Fully tighten the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSPECT FRONT SEAT OUTER BELT ASSEMBLY


    B131510E09
  1. Before installing the front seat outer belt assembly, check the ELR function.

    NOTICE:
    Do not disassemble the retractor.


    1. When the inclination of the retractor is 15° or less, check that the belt can be pulled from the retractor. When the inclination of the retractor is over 45°, check that the belt locks.
      Text in Illustration 
      *1
      Retractor
      *a
      Unlocked
      *b
      Locked
      *c
      45°
      If the result is not as specified, replace the front seat outer belt assembly.



3. INSTALL FRONT SEAT OUTER BELT ASSEMBLY


    B271085E02
  1. Install the bolt (A) first, then the bolt (B) to temporarily install the front seat outer belt assembly.

  1. Fully tighten the 2 bolts.

    Torque:
    Bolt (A):
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }
    Bolt (B):
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B271087
  1. Connect the pretensioner connector and lock the locking button as shown in the illustration.

    NOTICE:
    Securely lock the locking button.

  1. Connect the shoulder anchor of the front seat outer belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL CENTER PILLAR UPPER GARNISH (for TMMK Made)
  1. Install a new clip to the center pillar upper garnish LH.

  1. Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH.

  1. Engage the clip.

  1. Install the center pillar upper garnish LH with the 2 screws.



5. INSTALL CENTER PILLAR UPPER GARNISH (for TMC, TMMR Made)
  1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.

  1. Engage the clip.

  1. Install the center pillar upper garnish LH with the 2 screws.



6. INSTALL CENTER PILLAR LOWER GARNISH (for TMMK Made)
  1. Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.



7. INSTALL CENTER PILLAR LOWER GARNISH (for TMC, TMMR Made)
  1. Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.



8. CONNECT FRONT SEAT OUTER BELT ASSEMBLY
  1. Install the floor anchor of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Check if the ELR locks.

    NOTICE:
    The check should be performed with the front seat outer belt assembly installed.


    1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.



9. INSTALL LAP BELT OUTER ANCHOR COVER
  1. Engage the 3 claws to install the lap belt outer anchor cover.



10. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP (for TMMK Made)
for LH Side:
for RH Side:


11. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP (for TMC, TMMR Made)
for LH Side:
for RH Side:


12. INSTALL REAR DOOR SCUFF PLATE (for TMMK Made)
  1. Engage the 6 claws to install the rear door scuff plate LH.

    HINT:
    Engage the claws from the rear side of the scuff plate.



13. INSTALL REAR DOOR SCUFF PLATE (for TMC, TMMR Made)
  1. Engage the 6 claws to install the rear door scuff plate LH.

    HINT:
    Engage the claws from the rear side of the scuff plate.



14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP (for TMMK Made)
for LH Side:
for RH Side:


15. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP (for TMC, TMMR Made)
for LH Side:
for RH Side:


16. INSTALL FRONT DOOR SCUFF PLATE (for TMMK Made)
  1. Engage the 10 claws to install the front door scuff plate LH.



17. INSTALL FRONT DOOR SCUFF PLATE (for TMC, TMMR Made)
  1. Engage the 10 claws to install the front door scuff plate LH.



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



19. INSPECT SRS WARNING LIGHT (for TMMK Made)
(Click here)


20. INSPECT SRS WARNING LIGHT (for TMC, TMMR Made)
(Click here)