PARK / NEUTRAL POSITION SWITCH > INSTALLATION |
| 1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.
![]() |
Align the protrusions of the park/neutral position switch assembly as shown in the illustration.
| *a | Protrusion |
Hold the park/neutral position switch assembly in position and tighten the 2 bolts.
Connect the park/neutral position switch assembly connector.
| 2. INSTALL TRANSMISSION CONTROL SHAFT LEVER |
Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the washer and nut.
| 3. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
Move the shift lever to N.
Connect the transmission control cable assembly to the transmission control shaft lever with the nut.
Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
| 4. CONNECT ENGINE WIRE |
Engage the clamp to connect the engine wire to the automatic transaxle assembly.
Install the nut to the wire harness clamp bracket.
| 5. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Insert the projection of the air cleaner case sub-assembly into the hole of the No. 1 air cleaner bracket as shown in the illustration.
| *a | Hole |
| *b | Projection |
Install the 2 bolts.
Connect the wire harness clamp.
| 6. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.
| 7. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE |
Connect the air cleaner cap with air cleaner hose to the throttle body with motor assembly.
Install the air cleaner cap with air cleaner hose with the 2 guides and 2 air cleaner cap clamps.
Tighten the hose clamp.
Connect the union to connector tube hose to the air cleaner hose sub-assembly.
Engage the wire harness clamp.
Connect the mass air flow meter sub-assembly connector.
Engage the ventilation hose clamp.
Connect the ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.
| 8. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner assembly with the 2 bolts.
| 9. INSTALL COOL AIR INTAKE DUCT SEAL |
Install the cool air intake duct seal with the 9 clips.
| 10. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION |
Apply the parking brake.
Turn the engine switch on (IG).
Depress the brake pedal and check that the engine starts when the shift lever is in N or P, but does not start in any other position.
Check that the back-up lights come on when the shift lever is moved to R, but do not come on in any other position. If the operation is not as specified, check the park/neutral position switch assembly for continuity.
| 11. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
Engage the 3 grommets to install the No. 1 engine cover sub-assembly.
| 12. INSPECT SHIFT LEVER POSITION |
When the shift lever is moved from P to R with the engine switch ON and brake pedal depressed, make sure that the shift lever moves smoothly and correctly to P.
Start the engine and check that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.
| 13. ADJUST SHIFT LEVER POSITION |
Move the shift lever to N.
Remove the console box assembly (Click here).
![]() |
Disconnect the end of the transmission control cable assembly from the lower shift lever assembly.
Disengage the 2 claws and disconnect the transmission control cable assembly from the lower shift lever assembly.
![]() |
Slide the slider of the transmission control cable assembly as shown in the illustration and pull the lock piece outward.
| *a | Slider |
| *b | Lock Piece |
| *c | Slide |
| *d | Pull |
![]() |
Engage the 2 claws to connect the transmission control cable assembly to the lower shift lever assembly.
| *a | Lock Piece |
Connect the end of the transmission control cable assembly to the lower shift lever assembly.
Push the lock piece into the adjuster case.
After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.
Install the console box assembly (Click here).