Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

DTC    B15DA    Rear Console Recognition Disconnected

for Preparation Click here


DESCRIPTION

The stereo component amplifier assembly and rear control switch are connected via AVC-LAN communication lines.
The radio and display receiver assembly is also connected to the stereo component amplifier assembly via AVC-LAN communication lines.
This DTC is stored when an AVC-LAN communication error occurs between the stereo component amplifier assembly and rear control switch.

HINT:
If B15DA and B15D3 are output at the same time, troubleshoot for B15D3 first.


DTC No.
DTC Detection Condition
Trouble Area
B15DA
When either of the following conditions is met:
  1. Rear control switch is not connected while the ignition switch is ACC or ON.
  2. Communication between the master unit and the rear control switch is not possible when the engine is started.
  1. Rear control switch power source circuit
  2. AVC-LAN circuit between radio and display receiver assembly and rear control switch
  3. Rear control switch
  4. Stereo component amplifier assembly
  5. Radio and display receiver assembly
  6. Harness or connector

HINT:
  1. Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The radio and display receiver assembly is the master unit.


WIRING DIAGRAM


E296368E10


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK DTC
  1. If DTC B15D3 is output, perform troubleshooting for B15D3 first.

    Result:
    Result
    Proceed to
    B15D3 is not output
    A
    B15D3 is output
    B



B
GO TO DTC B15D3 (Click here)
A


2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result:
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

HINT:
  1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
  2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 4
A


3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


4.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 5
OK

END 

5.CHECK HARNESS AND CONNECTOR (REAR CONTROL SWITCH POWER SOURCE)
  1. Disconnect the X1 rear control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    X1-16 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    X1-1 (+B) - X1-16 (GND)
    Always
    11 to 14 V
    X1-7 (IG+) - X1-16 (GND)
    Ignition switch ON
    11 to 14 V
    X1-6 (ACC) - X1-16 (GND)
    Ignition switch ACC
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR CONTROL SWITCH)
  1. Disconnect the I69 stereo component amplifier assembly connector.

  1. Disconnect the X1 rear control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I69-20 (TXD+) - X1-15 (TX+)
    Always
    Below 1 Ω
    I69-19 (TXD-) - X1-5 (TX-)
    Always
    Below 1 Ω
    I69-20 (TXD+) - Body ground
    Always
    10 kΩ or higher
    I69-19 (TXD-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.REPLACE REAR CONTROL SWITCH
  1. Replace the rear control switch (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 8
OK

END 

8.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END