DTC B15C0 Short in GPS Antenna |
DTC B15C1 Open in GPS Antenna |
| DTC No. | DTC Detection Condition | Trouble Area |
| B15C0 | Navigation antenna malfunction |
|
| B15C1 | Navigation antenna power source malfunction |
| 1.CHECK DTC |
Clear the DTCs (Click here).
Recheck for DTCs and check that no DTCs are output.
|
| ||||
| OK | ||
| ||
| 2.CHECK MODEL |
Choose the model to be inspected.
| Result | Proceed to |
| w/ Heated Windshield Defroster System | A |
| w/o Heated Windshield Defroster System | B |
|
| ||||
| A | |
| 3.CHECK ANTENNA CORD SUB-ASSEMBLY |
![]() |
Disconnect the antenna cord sub-assembly connector from the radio and display receiver assembly.
| *a | Antenna cord sub-assembly connector (to Radio and Display Receiver Assembly) |
![]() |
Disconnect the antenna cord sub-assembly connector from the No. 2 antenna cord sub-assembly.
| *a | Antenna cord sub-assembly connector (to No. 2 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-1 - B-1 | Always | Below 1 Ω |
| A-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY |
![]() |
Disconnect the No. 2 antenna cord sub-assembly connector from the antenna cord sub-assembly.
| *a | No. 2 antenna cord sub-assembly connector (to Antenna Cord Sub-assembly) |
![]() |
Disconnect the No. 2 antenna cord sub-assembly connector from wire harness.
| *a | No. 2 antenna cord sub-assembly connector (to Wire Harness) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C-1 - D-2 | Always | Below 1 Ω |
| C-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (NAVIGATION ANTENNA ASSEMBLY - NO. 2 ANTENNA CORD SUB-ASSEMBLY) |
![]() |
Disconnect the wire harness connector from the No. 2 antenna cord sub-assembly connector.
| *a | Front view of wire harness connector (to No. 2 Antenna Cord Sub-assembly) |
![]() |
Disconnect the wire harness connector from the navigation antenna assembly.
| *a | Front view of wire harness connector (to Navigation Antenna Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E-2 - F-2 | Always | Below 1 Ω |
| E-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.INSPECT NAVIGATION ANTENNA ASSEMBLY |
Remove the navigation antenna assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 - 2a | Always | 50 to 500 Ω |
| *a | Component without harness connected (Navigation Antenna Assembly) |
|
| ||||
| OK | ||
| ||
| 7.INSPECT NAVIGATION ANTENNA ASSEMBLY |
Remove the navigation antenna assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 1a | Always | 50 to 500 Ω |
| *a | Component without harness connected (Navigation Antenna Assembly) |
|
| ||||
| OK | ||
| ||