SFI SYSTEM > VC Output Circuit |



| 1.CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.
|
| ||||
| OK | ||
| ||
| 2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Check the communication between the tester and ECM.
| Result | Proceed to |
| Communication is not possible | A |
| Communication is possible | B |
|
| ||||
| A | |
| 3.CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle with motor body assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR) |
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate (w/ tumble control valve) | A |
| MIL illuminates | B |
| MIL does not illuminate (w/o tumble control valve) | C |
|
| ||||
|
| ||||
| A | |
| 5.CHECK MIL (INTAKE AIR CONTROL VALVE ACTUATOR (FOR TUMBLE CONTROL VALVE)) |
Disconnect the intake air control valve actuator (for tumble control valve) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 6.CHECK MIL (CAMSHAFT POSITION SENSOR FOR INTAKE CAMSHAFT) |
Disconnect the camshaft position sensor (for intake camshaft) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 7.CHECK MIL (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT) |
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Turn the ignition switch to ON.
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 8.CHECK HARNESS AND CONNECTOR |
Disconnect the camshaft position sensor (for exhaust camshaft) connector.
Disconnect the camshaft position sensor (for intake camshaft) connector.
Disconnect the throttle with motor body assembly connector.
Disconnect the intake air control valve actuator (for tumble control valve) connector*.
*: w/ tumble control valve
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E26-111 (VCE1) - Body ground | Always | 10 kΩ or higher |
| E26-113 (VCV1) - Body ground | Always | 10 kΩ or higher |
| E26-125 (VCTA) - Body ground | Always | 10 kΩ or higher |
| E26-130 (VCIA)* - Body ground | Always | 10 kΩ or higher |
| A25-53 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A25-56 (VCP2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||