Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for TMMK Made)

AIR CONDITIONING UNIT (for TMMK Made) > REMOVAL

for Preparation Click here


NOTICE:
Make sure to select FACE mode before disconnecting the cable from the negative (-) battery terminal.



1. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
  1. Turn the A/C switch on.

  1. Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.

  1. Turn the ignition switch off.

  1. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.



2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


3. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY


  1. w/ Windshield Deicer System:



      C309273
    1. Disengage the 2 clamps.

    2. Disconnect the connector and separate the wire harness from the front outer cowl top panel sub-assembly.



  1. w/ Heated Windshield Defroster System:



      C309274
    1. Disengage the 4 clamps.

    2. Disconnect the 2 connectors and separate the wire harness from the front outer cowl top panel sub-assembly.



    C239198
  1. Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.



    C239185
  1. Remove the 10 bolts and front outer cowl top panel sub-assembly.



4. DISCONNECT HEATER OUTLET WATER HOSE


    E227145
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.

    NOTICE:
    1. Do not apply excessive force to the heater outlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



5. DISCONNECT HEATER INLET WATER HOSE


    E227146
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater inlet water hose.

    NOTICE:
    1. Do not apply excessive force to the heater inlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.



6. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    E227144
  1. Remove the bolt and rotate the hook connector as shown in the illustration.

  1. Disconnect the suction hose sub-assembly.

  1. Remove the O-ring from the suction hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



7. DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY
  1. Disconnect the air conditioner tube and accessory assembly.

  1. Remove the O-ring from the air conditioner tube and accessory assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



8. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
(Click here)


9. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
(Click here)


10. REMOVE AUDIO AMPLIFIER COVER (for 10 Speakers)


    E223732
  1. Using a clip remover, remove the 2 clips and audio amplifier cover.



11. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)


    E223733
  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect each connector and disengage the clamp.



    E223734
  1. Remove the bolt.

  1. Disengage the 2 guides and remove the stereo component amplifier assembly with bracket.



12. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

HINT:
Use the same procedure as for the LH side.



13. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:
Use the same procedure as for the LH side.



14. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
(Click here)


15. REMOVE STEERING POST ASSEMBLY
(Click here)


16. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    B287216
  1. Disconnect the 5 connectors.



    B279017
  1. Remove the bolt, 2 nuts and disconnect the instrument panel junction block assembly.



    B279018
  1. Disengage the claw and disconnect the connector as shown in the illustration.



    B279020
  1. Disengage the claw and slide the connector lock as shown in the illustration.



    B279022
  1. Disengage the claw and disconnect the connector as shown in the illustration.

  1. Remove the instrument panel junction block assembly.



17. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Disconnect each connector.



    E226869
  1. Remove the 2 screws.

  1. Disengage the 2 guides to remove the air conditioning amplifier assembly.



18. REMOVE FLOOR CARPET HOOK


    E227413E02
  1. Disengage the 6 guides.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



    E227415E02
  1. Disengage the 6 claws and remove the 6 floor carpet hooks.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



19. DISCONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    E227149
  1. Remove the screw.



    E227150
  1. Disengage the guide to disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.



20. REMOVE FRONT FLOOR CARPET LH


    E296243E01
  1. Disengage the guide and each fastener, and remove the front floor carpet LH.
    Text in Illustration 
    *a
    Fastener



21. REMOVE REAR NO. 4 AIR DUCT


    E227157
  1. Disengage the 4 claws to remove the rear No. 4 air duct as shown in the illustration.



22. REMOVE FLOOR CARPET BRACKET LH


    E227160
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket LH.



23. REMOVE REAR NO. 3 AIR DUCT


    E227161
  1. Disengage the 2 claws to remove the rear No. 3 air duct.



24. REMOVE FRONT FLOOR CARPET RH


    E296244E01
  1. Disengage the guide and each fastener, and remove the front floor carpet RH.
    Text in Illustration 
    *a
    Fastener



25. REMOVE REAR NO. 2 AIR DUCT


    E227156
  1. Disengage the 4 claws to remove the rear No. 2 air duct as shown in the illustration.



26. REMOVE FLOOR CARPET BRACKET RH


    E227159
  1. Remove the 2 clips.

  1. Disengage the 2 guides to remove the floor carpet bracket RH.



27. REMOVE REAR NO. 1 AIR DUCT


    E227162
  1. Disengage the 2 claws to remove the rear No. 1 air duct.



28. REMOVE NO. 1 CONSOLE BOX DUCT


    E227163
  1. Remove the clip and No. 1 console box duct.



29. REMOVE ROOM TEMPERATURE SENSOR (COOLER THERMISTOR)
  1. Disconnect the cooler thermistor hose and connector, and remove the room temperature sensor (cooler thermistor).



30. REMOVE INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY


    E315379E01
  1. Disengage each clamp.
    Text in Illustration 
    *a
    Earth Wire

  1. Remove the bolt and disconnect the earth wire.



    E296246
  1. Remove the bolt and 2 nuts.

  1. Remove the screw and instrument panel to cowl brace sub-assembly.



31. REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    E296247E01
  1. Disconnect each connector.
    Text in Illustration 
    *a
    Earth Wire

  1. Disengage each clamp.

  1. Remove the bolt and disconnect the earth wire.



    E227165
  1. Remove the bolt and 2 nuts.

  1. Remove the screw and No. 2 instrument panel brace sub-assembly.



32. REMOVE INSTRUMENT PANEL SAFETY PAD CAP


    E227183E02
  1. Put protective tape around the 5 instrument panel safety pad caps.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side
    *a
    Protective Tape

  1. Using a screwdriver, remove the 5 instrument panel safety pad caps as shown in the illustration.



33. REMOVE FRONT LOWER PANEL PACKING


    E227177
  1. Remove the 2 front lower panel packings as shown in the illustration.



34. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT

NOTICE:
  1. Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.
  2. When disassembling the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



  1. for 10 Speakers:



      E234881
    1. Disengage the 3 clamps.



    E227851
  1. Disengage the 3 claws to open the 3 clamps as shown in the illustration.



    E234883E03
  1. Disconnect the connector from the airbag sensor assembly as shown in the illustration.
    Text in Illustration 
    *1
    Airbag Sensor Assembly

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  1. Disconnect each connector.

  1. Disengage each clamp.



  1. Using a screwdriver, disengage the 2 claws to unlock the retainer as shown in the illustration.


    E227173E03


    Text in Illustration 
    *a
    Retainer
    *b
    Protective Tape



  1. Disengage the claw and disconnect the airbag connector as shown in the illustration.


    E227175



  1. Disengage each clamp.


    E296248E01


    Text in Illustration 
    *a
    Earth Wire
    -
    -

  1. Remove the 2 bolts and disconnect the 2 earth wires.



    E234885
  1. Disengage each clamp.



  1. Remove the bolt and disconnect the earth wire.


    E234886E03


    Text in Illustration 
    *a
    Earth Wire
    *b
    Connector Holder

  1. Remove the 2 nuts and disconnect the connector holder.

  1. Disconnect the connector.

  1. Disengage each clamp.



    E227179
  1. Remove the 2 bolts.



    E231353
  1. Disconnect the drain cooler hose.



  1. Remove the 6 bolts and nut as shown in the illustration.


    E315343E01


    Text in Illustration 
    *1
    Movable Collar
    *2
    Instrument Panel Reinforcement Assembly
    *a
    Vehicle Body
    *b
    Step 1
    *c
    Step 2
    *d
    Step 3
    *e
    Step 4
    -
    -



  1. Disengage the 3 guides and remove the instrument panel reinforcement assembly with air conditioning unit as shown in the illustration.


    E315344



35. REMOVE AIR CONDITIONING UNIT ASSEMBLY


  1. Remove the 3 bolts and air conditioning unit assembly from the instrument panel reinforcement assembly.


    E315345