RADIATOR > INSTALLATION |
| 1. INSTALL RADIATOR ASSEMBLY |
Engage the 2 guides.
Engage the 3 claws and install the fan assembly to the radiator assembly.
Install the 2 lower radiator supports to the radiator assembly.
![]() |
Install the radiator assembly with the fan assembly to the vehicle.
Install the condenser assembly to the radiator assembly with the 4 bolts.
Engage the 2 clamps.
Connect the cooling fan motor connector and No. 2 cooling fan motor connector.
| 2. INSTALL UPPER RADIATOR SUPPORT |
Install the 2 radiator support cushions to the radiator assembly.
Install the upper radiator support with the 5 bolts.
Engage the clamp and connect the hood lock control cable assembly to the upper radiator support.
Connect the 2 horn connectors.
| 3. INSTALL HOOD LOCK ASSEMBLY |
![]() |
Apply MP grease to the sliding areas of the lock.
Connect the hood lock control cable assembly.
Install the hood lock assembly with the 2 bolts and hood lock bolt.
Connect the connector.
| 4. CONNECT OUTLET NO. 1 OIL COOLER HOSE |
Connect the outlet No. 1 oil cooler hose and slide the clip to secure it.
| 5. CONNECT INLET NO. 1 OIL COOLER HOSE |
Connect the inlet No. 1 oil cooler hose and slide the clip to secure it.
| 6. CONNECT NO. 2 RADIATOR HOSE |
Engage the clamp and connect the No. 2 radiator hose to the fan assembly.
Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.
| 7. CONNECT NO. 1 RADIATOR HOSE |
Connect the No. 1 radiator hose to the radiator assembly and slide the clip to secure it.
| 8. INSTALL RADIATOR RESERVE TANK ASSEMBLY |
Install the radiator reserve tank assembly with the 2 bolts.
Connect the radiator reserve tank hose.
| 9. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner assembly with the 2 bolts.
| 10. INSTALL FRONT BUMPER ASSEMBLY |
| 11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 12. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Slowly fill the radiator assembly with engine coolant.
Remove the reserve tank cap.
Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.
If the engine coolant level is low, add engine coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the cooling system.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 13. INSPECT FOR COOLANT LEAK |
Remove the radiator cap sub-assembly.
![]() |
Fill the radiator assembly with engine coolant, and then install a radiator cap tester.
| *a | Radiator Cap Tester |
Warm up the engine.
Pump the radiator cap tester to 118 kPa (1.2 kgf/cm2, 17 psi), and then check that the pressure does not drop.
Remove the radiator cap tester.
Install the radiator cap sub-assembly.
| 14. INSTALL ENGINE UNDER COVER LH |
| 15. INSTALL ENGINE UNDER COVER RH |
| 16. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
| 17. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |