Home › Engine / Hybrid System ยท 2AR-FE › FUEL › FUEL PUMP (for TMC, TMMR Made)

FUEL PUMP (for TMC, TMMR Made) > INSTALLATION

for Preparation Click here



1. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    A136023E02
  1. Install a new fuel suction tube set gasket to the fuel suction tube.
    Text in Illustration 
    *1
    Fuel Suction Tube Set Gasket

  1. Install the fuel suction tube with pump and gauge assembly to the fuel tank.

    NOTICE:
    1. Do not damage the suction filter.
    2. Be careful that the arm of the sender gauge does not bend.



2. INSTALL FUEL TANK VENT TUBE SET PLATE


    A129480E02
  1. Align the mark of the set plate with the fuel suction tube.
    Text in Illustration 
    *a
    Mark

  1. Install the set plate with the 8 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



3. CONNECT FUEL PUMP TUBE SUB-ASSEMBLY


    A255956E01
  1. Push the fuel tube joint onto the plug of the fuel suction plate, then install the tube joint clip.
    Text in Illustration 
    *1
    Tube Joint Clip
    *2
    Fuel Tube Joint
    *3
    O-ring
    *4
    Collar
    *a
    Correct
    *b
    Incorrect

    NOTICE:
    1. Check that there are no scratches or foreign matter around the connected part of the fuel tube joint and plug before performing this work.
    2. Check that the fuel tube joint is securely inserted to the end.
    3. Check that the tube joint clip is on the collar of the fuel tube joint.
    4. After installing the tube joint clip, check that the fuel tube joint cannot be pulled out.

  1. Connect the fuel pump connector.



4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



5. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON and turn the intelligent tester on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the ignition switch off.

  1. Disconnect the intelligent tester from the DLC3.



6. INSTALL REAR FLOOR SERVICE HOLE COVER


    A254976
  1. Install the rear floor service hole cover with new butyl tape.
    Text in Illustration 
    V100144
    Butyl Tape



7. INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    B393388
  1. Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



8. INSTALL REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    B393388
  1. Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure as for the LH side.



9. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. w/ Seat Heater System:

    1. Engage the 2 clamps.

    2. Connect the connector.



    B383049
  1. Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

  1. Confirm that the rear seat cushion assembly is firmly installed.

    NOTICE:
    When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.



10. INSTALL REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)
  1. Place the rear seat cushion assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly.

  1. Connect the 2 seat heater connectors.



    B290775
  1. Engage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly to the 2 rear seat cushion lock hooks as shown in the illustration.

  1. Confirm that the rear seat cushion assembly is securely installed.

    NOTICE:
    When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.