Home › Engine / Hybrid System ยท 2AR-FE › FUEL › FUEL PUMP (for TMMK Made)

FUEL PUMP (for TMMK Made) > REMOVAL

for Preparation Click here


HINT:
Perform "Inspection After Repair" after replacing the fuel pump with filter assembly (Click here).



1. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. REMOVE REAR SEAT CUSHION ASSEMBLY


    B279202E01
  1. Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
    Standard Measurement 
    a
    100 mm (3.94 in.) or less

    NOTICE:
    Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

  1. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

    NOTICE:
    Be careful not to damage the vehicle body.



5. REMOVE REAR SEAT CUSHION LOCK HOOK


    B393387
  1. Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

    NOTICE:
    Rear seat cushion lock hooks must not be reused.

    HINT:
    Use the same procedure for the RH side and the LH side.



6. REMOVE REAR FLOOR SERVICE HOLE COVER


    A299888
  1. Remove the rear floor service hole cover.

  1. Disconnect the fuel pump connector.



7. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A299889E02
  1. Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.
    Text in Illustration 
    *1
    Tube Joint Clip
    *2
    Fuel Tank Main Tube Sub-assembly
    *3
    Fuel Suction Plate Sub-assembly
    *a
    Fuel Tube Joint
    *b
    O-ring
    V100135
    Pull off
    V100136
    Pull off

    NOTICE:
    1. Remove any foreign matter on the fuel tube joint before performing this work.
    2. Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
    3. Be sure to disconnect the fuel tube joint by hand.
    4. Do not bend, twist, pinch or kink the fuel tank main tube sub-assembly.
    5. Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube joint.
    6. If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.



8. DISCONNECT FUEL EMISSION HOSE


    A299890
  1. Slide the clip and disconnect the fuel emission hose from the fuel suction tube with pump and gauge assembly.



9. DISCONNECT NO. 2 CHARCOAL CANISTER OUTLET HOSE


    A299891
  1. Slide the clip and disconnect the No. 2 charcoal canister outlet hose from the fuel suction tube with pump and gauge assembly.



10. REMOVE FUEL TANK VENT TUBE SET PLATE


    A299892
  1. Remove the 8 bolts and fuel tank vent tube set plate.



11. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    A347574E01
  1. Using a screwdriver with its tip wrapped with protective tape, pull the retainer to disengage the lock claws and pull out the fuel cut-off tube.
    Text in Illustration 
    *1
    Fuel Suction Tube Set Gasket
    *a
    Retainer
    *b
    Fuel Cut-off Tube
    V100135
    Pull
    V100136
    Pull out

  1. Remove the fuel suction tube with pump and gauge assembly from the fuel tank sub-assembly.

    NOTICE:
    1. Be careful not to bend the arm of the fuel sender gauge assembly.
    2. Do not damage the tube and fuel pump harness.

  1. Remove the fuel suction tube set gasket from the fuel suction tube with pump and gauge assembly.