Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING (for TMMK Made)

REAR DOOR WINDOW FRAME MOULDING (for TMMK Made) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. INSTALL REAR DOOR REAR WINDOW FRAME MOULDING


    B381024
  1. Using an air riveter or hand riveter with a nose piece, install the rear door rear window frame moulding with 4 new rivets.

    HINT:
    If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

    NOTICE:

    1. B125583E10
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
      Text in Illustration 
      *a
      Riveter
      *b
      Mandrel
      *c
      Incorrect

    2. B125584E11
      Confirm that the rivets are seated properly against the moulding.
      Text in Illustration 
      *a
      Riveter
      *b
      Incorrect
    3. Do not tilt the riveter when installing the rivet to the moulding.
    4. Do not leave any space between the rivet head and moulding.

    5. B125585E13
      Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.
      Text in Illustration 
      *a
      Riveter
      *b
      Incorrect



2. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING


    B381022
  1. Engage the guide of the rear door upper window frame moulding to the door frame.

  1. Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding with 4 new rivets.

    HINT:
    If the mandrel of the rivet does not come off on the first operation of the rivet gun, slide the rivet gun forward on the mandrel and operate it again.

    NOTICE:

    1. B125583E10
      Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.
      Text in Illustration 
      *a
      Riveter
      *b
      Mandrel
      *c
      Incorrect

    2. B125584E11
      Confirm that the rivets are seated properly against the moulding.
      Text in Illustration 
      *a
      Riveter
      *b
      Incorrect
    3. Do not tilt the riveter when installing the rivet to the moulding.
    4. Do not leave any space between the rivet head and moulding.

    5. B125585E13
      Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.
      Text in Illustration 
      *a
      Riveter
      *b
      Incorrect



3. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:
When installing a new rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

Heating Temperature 
Item
Temperature
Vehicle Body
40 to 60°C (104 to 140°F)
Rear Door Front Window Frame Moulding
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the vehicle body or rear door front window frame moulding excessively.

  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove any remaining double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Using a heat light, heat the vehicle body and rear door front window frame moulding.

  1. Remove the release paper from a new rear door front window frame moulding.

    HINT:
    After removing the release paper, keep the exposed adhesive free from foreign matter.



    B381020E01
  1. Engage the clip and guide, and attach the double-sided tape to install the rear door front window frame moulding.
    Text in Illustration 
    *a
    Caulking Sponge
    V100155
    Double-sided Tape



4. INSTALL REAR DOOR BELT MOULDING ASSEMBLY


    B380986
  1. Engage the 6 claws to install the rear door belt moulding assembly as shown in the illustration.



5. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B380668
  1. Slide the rear door glass sub-assembly to install it as shown in the illustration.

    NOTICE:
    Do not damage the rear door glass sub-assembly.



6. INSTALL REAR DOOR QUARTER WINDOW GLASS
  1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.



    B280411
  1. Install the rear door quarter window glass together with the rear door quarter window weatherstrip as shown in the illustration.



7. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B380666
  1. Install the rear door lower window frame sub-assembly with the screw and 2 bolts.



8. INSTALL REAR DOOR GLASS RUN


    B380665
  1. Install the rear door glass run.



9. INSTALL REAR DOOR WEATHERSTRIP


    B380664
  1. Engage the 20 clips to install the rear door weatherstrip.



10. INSTALL REAR DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding parts of the rear door check assembly.

  1. Clean the bolt hole on the vehicle body.

  1. Clean the bolt threads of the bolt.

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



    B280406
  1. Install the rear door check assembly with the 2 nuts and bolt.

    Torque:
    Bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    Nut:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



11. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the rear door panel.



    B380669E01
  1. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
    Text in Illustration 
    *a
    Reference Point

  1. Install the rear door service hole cover according to the reference points on the rear door panel.

    NOTICE:
    Securely install the rear door service hole cover preventing wrinkles and air bubbles.

  1. Connect the connector.



12. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    B380670
  1. Install the rear door inner glass weatherstrip.



13. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B380671
  1. Install the No. 1 door scuff plate clamp as shown in the illustration.



    B380662E01
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly



    B380663E01
  1. Engage the 4 claws and reference boss as shown in the illustration.
    Text in Illustration 
    *a
    Reference Boss



    B380659
  1. Engage the 8 clips to install the rear door trim board sub-assembly.

  1. Install the 3 screws.



14. INSTALL REAR ARMREST ASSEMBLY


    B280392
  1. Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.



15. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
  1. Connect the connector.



    B380657
  1. Engage the 3 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.



16. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    B280388
  1. Engage the 3 claws to install the rear door inside handle bezel plug.



17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



18. INSPECT POWER WINDOW OPERATION
(Click here)