REAR DOOR WINDOW FRAME MOULDING (for TMMK Made) > INSTALLATION |
| 1. INSTALL REAR DOOR REAR WINDOW FRAME MOULDING |
![]() |
Using an air riveter or hand riveter with a nose piece, install the rear door rear window frame moulding with 4 new rivets.
![]() |
| *a | Riveter |
| *b | Mandrel |
| *c | Incorrect |
![]() |
| *a | Riveter |
| *b | Incorrect |
![]() |
| *a | Riveter |
| *b | Incorrect |
| 2. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING |
![]() |
Engage the guide of the rear door upper window frame moulding to the door frame.
Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding with 4 new rivets.
![]() |
| *a | Riveter |
| *b | Mandrel |
| *c | Incorrect |
![]() |
| *a | Riveter |
| *b | Incorrect |
![]() |
| *a | Riveter |
| *b | Incorrect |
| 3. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Rear Door Front Window Frame Moulding | 20 to 30°C (68 to 86°F) |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and rear door front window frame moulding.
Remove the release paper from a new rear door front window frame moulding.
![]() |
Engage the clip and guide, and attach the double-sided tape to install the rear door front window frame moulding.
| *a | Caulking Sponge |
![]() | Double-sided Tape |
| 4. INSTALL REAR DOOR BELT MOULDING ASSEMBLY |
![]() |
Engage the 6 claws to install the rear door belt moulding assembly as shown in the illustration.
| 5. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Slide the rear door glass sub-assembly to install it as shown in the illustration.
| 6. INSTALL REAR DOOR QUARTER WINDOW GLASS |
Install the rear door quarter window glass to the rear door quarter window weatherstrip.
![]() |
Install the rear door quarter window glass together with the rear door quarter window weatherstrip as shown in the illustration.
| 7. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
![]() |
Install the rear door lower window frame sub-assembly with the screw and 2 bolts.
| 8. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 9. INSTALL REAR DOOR WEATHERSTRIP |
![]() |
Engage the 20 clips to install the rear door weatherstrip.
| 10. INSTALL REAR DOOR CHECK ASSEMBLY |
Apply MP grease to the sliding parts of the rear door check assembly.
Clean the bolt hole on the vehicle body.
Clean the bolt threads of the bolt.
Apply adhesive to the threads of the bolt.
![]() |
Install the rear door check assembly with the 2 nuts and bolt.
| 11. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply new butyl tape to the rear door panel.
![]() |
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
| *a | Reference Point |
Install the rear door service hole cover according to the reference points on the rear door panel.
Connect the connector.
| 12. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Install the rear door inner glass weatherstrip.
| 13. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Install the No. 1 door scuff plate clamp as shown in the illustration.
![]() |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
![]() |
Engage the 4 claws and reference boss as shown in the illustration.
| *a | Reference Boss |
![]() |
Engage the 8 clips to install the rear door trim board sub-assembly.
Install the 3 screws.
| 14. INSTALL REAR ARMREST ASSEMBLY |
![]() |
Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.
| 15. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
Connect the connector.
![]() |
Engage the 3 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.
| 16. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws to install the rear door inside handle bezel plug.
| 17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 18. INSPECT POWER WINDOW OPERATION |