REAR DOOR WINDOW FRAME MOULDING (for TMC, TMMR Made) > INSTALLATION |
| 1. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING |
![]() |
Engage the guide of the rear door upper window frame moulding to the door frame.
Using an air riveter or hand riveter with a nose piece, install the rear door upper window frame moulding with 6 new rivets.
![]() |
| *1 | Riveter |
| *2 | Mandrel |
| *a | Incorrect |
![]() |
| *1 | Riveter |
| *a | Incorrect |
![]() |
| *1 | Riveter |
| *a | Incorrect |
| 2. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Moulding | 20 to 30°C (68 to 86°F) |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
![]() |
Install a new rear door front window frame moulding.
| *1 | Double-sided Tape |
| *2 | Caulking Sponge |
Using a heat light, heat the vehicle body and rear door front window frame moulding.
Remove the release paper from the rear door front window frame moulding.
Install the rear door front window frame moulding with the clip.
| 3. INSTALL REAR DOOR BELT MOULDING ASSEMBLY |
![]() |
Engage the 6 claws to install the rear door belt moulding assembly as shown in the illustration.
| 4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Slide the rear door glass sub-assembly to install it as shown in the illustration.
| 5. INSTALL REAR DOOR QUARTER WINDOW GLASS |
Install the rear door quarter window glass to the rear door quarter window weatherstrip.
![]() |
Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.
| 6. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
![]() |
Install the rear door lower window frame sub-assembly with the screw and 2 bolts.
| 7. INSTALL REAR DOOR GLASS RUN |
![]() |
Install the rear door glass run.
| 8. INSTALL REAR DOOR WEATHERSTRIP |
![]() |
Engage the 20 clips to install the rear door weatherstrip.
| 9. INSTALL REAR DOOR CHECK ASSEMBLY |
Apply MP grease to the sliding parts of the rear door check assembly.
Apply adhesive to the threads of the bolt.
![]() |
Install the rear door check assembly with the 2 nuts and bolt.
| 10. INSTALL REAR DOOR SERVICE HOLE COVER |
Apply new butyl tape to the rear door panel.
![]() |
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
| *1 | Reference Point |
Attach the rear door service hole cover according to the reference points on the rear door panel.
Connect the connector.
| 11. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Install the rear door inner glass weatherstrip.
| 12. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Install the No. 1 door scuff plate clamp as shown in the illustration.
![]() |
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
Connect the connector.
![]() |
Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.
| *1 | Reference Boss |
![]() |
Engage the 8 clips and install the rear door trim board sub-assembly.
Install the 3 screws.
If protective tape has been applied, remove it.
| 13. INSTALL REAR ARMREST ASSEMBLY |
![]() |
Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.
| 14. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
w/o Seat Heater System:
Connect the connector.
w/ Seat Heater System:
Connect the 2 connectors.
![]() |
Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.
| 15. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Engage the 3 claws to install the rear door inside handle bezel plug.
| 16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 17. INITIALIZE POWER WINDOW CONTROL SYSTEM |
| 18. INSPECT POWER WINDOW OPERATION |