REAR DOOR WINDOW FRAME MOULDING (for TMC, TMMR Made) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.
| 4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
w/o Seat Heater System:
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
w/ Seat Heater System:
Disconnect the 2 connectors and remove the rear power window regulator switch assembly with rear door armrest base panel.
| 5. REMOVE REAR ARMREST ASSEMBLY |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.
| 6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Put protective tape around the rear door panel.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 8 clips.
![]() |
Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
| *1 | Reference Boss |
| *2 | Rear Door Inner Glass Weatherstrip |
Disengage the reference boss from the rear door panel.
Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
![]() |
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
Disconnect the connector.
![]() |
Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 8. REMOVE REAR DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connector and remove the rear door service hole cover.
| 9. REMOVE REAR DOOR CHECK ASSEMBLY |
![]() |
Remove the bolt and 2 nuts and rear door check assembly.
| 10. REMOVE REAR DOOR WEATHERSTRIP |
![]() |
Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.
| 11. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the rear door glass run.
| 12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.
| 13. REMOVE REAR DOOR QUARTER WINDOW GLASS |
![]() |
Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
| 14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
| 15. REMOVE REAR DOOR BELT MOULDING ASSEMBLY |
![]() |
Put protective tape around the rear door belt moulding assembly.
| *1 | Protective Tape |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws to remove the rear door belt moulding assembly as shown in the illustration.
| *1 | Protective Tape |
| 16. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Moulding | 20 to 30°C (68 to 86°F) |
Using a heat light, heat the rear door front window frame moulding.
![]() |
Using a moulding remover, disengage the clip and remove the rear door front window frame moulding.
| *1 | Double-sided Tape |
| *2 | Caulking Sponge |
| 17. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING |
Insert a 4.0 mm (0.157 in.) drill bit into a drill.
![]() |
Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.
| Area | Dimension |
| A | 5.0 mm |
Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
Disengage the guide and remove the rear door upper window frame moulding from the door frame.