REAR DOOR BELT MOULDING (for TMMK Made) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel plug as shown in the illustration.
| 4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 3 guides.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
| 5. REMOVE REAR ARMREST ASSEMBLY |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides to remove the rear armrest assembly.
| 6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Apply protective tape to the rear door panel.
| *a | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 8 clips.
![]() |
Pull out the rear door trim board sub-assembly as shown in the illustration.
| *1 | Rear Door Inner Glass Weatherstrip |
| *a | Reference Boss |
Disengage the reference boss from the rear door panel.
Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
![]() |
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.
![]() |
Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
| *a | Screwdriver |
| 7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
| *a | Screwdriver |
| 8. REMOVE REAR DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connector.
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through the rear door service hole cover.
Remove the rear door service hole cover.
| 9. REMOVE REAR DOOR CHECK ASSEMBLY |
![]() |
Remove the bolt and 2 nuts, and rear door check assembly.
| 10. REMOVE REAR DOOR WEATHERSTRIP |
![]() |
Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.
| 11. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the rear door glass run.
| 12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and screw and rear door lower window frame sub-assembly.
| 13. REMOVE REAR DOOR QUARTER WINDOW GLASS |
![]() |
Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
| 14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
| 15. REMOVE REAR DOOR BELT MOULDING ASSEMBLY |
![]() |
Apply protective tape around the rear door belt moulding assembly as shown in the illustration.
![]() | Protective Tape |
![]() |
Using a screwdriver with its tip wrapped with protective tape, disengage the 6 claws to remove the rear door belt moulding assembly as shown in the illustration.
| *a | Screwdriver |
![]() | Protective Tape |