BLACK OUT TAPE (for Rear Door) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG (for TMMK Made) |
![]() |
Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel plug as shown in the illustration.
| 4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (for TMMK Made) |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 3 guides.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
| 5. REMOVE REAR ARMREST ASSEMBLY (for TMMK Made) |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides to remove the rear armrest assembly.
| 6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY (for TMMK Made) |
![]() |
Apply protective tape to the rear door panel.
| *a | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 8 clips.
![]() |
Pull out the rear door trim board sub-assembly as shown in the illustration.
| *1 | Rear Door Inner Glass Weatherstrip |
| *a | Reference Boss |
Disengage the reference boss from the rear door panel.
Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
![]() |
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.
![]() |
Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
| *a | Screwdriver |
| 7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP (for TMMK Made) |
![]() |
Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
| *a | Screwdriver |
| 8. REMOVE REAR DOOR SERVICE HOLE COVER (for TMMK Made) |
![]() |
Disconnect the connector.
Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through the rear door service hole cover.
Remove the rear door service hole cover.
| 9. REMOVE REAR DOOR CHECK ASSEMBLY (for TMMK Made) |
![]() |
Remove the bolt and 2 nuts, and rear door check assembly.
| 10. REMOVE REAR DOOR WEATHERSTRIP (for TMMK Made) |
![]() |
Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.
| 11. REMOVE REAR DOOR GLASS RUN (for TMMK Made) |
![]() |
Remove the rear door glass run.
| 12. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY (for TMMK Made) |
![]() |
Remove the 2 bolts and screw and rear door lower window frame sub-assembly.
| 13. REMOVE REAR DOOR QUARTER WINDOW GLASS (for TMMK Made) |
![]() |
Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
| 14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY (for TMMK Made) |
![]() |
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
| 15. REMOVE REAR DOOR FRAME GARNISH (for TMMK Made) |
![]() |
Disengage the clip and remove the rear door frame garnish.
| 16. REMOVE NO. 2 BLACK OUT TAPE (for TMMK Made) |
Using a heat light, heat the No. 2 black out tape and vehicle body.
| Item | Temperature |
| Vehicle Body and No. 2 Black Out Tape | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the No. 2 black out tape to remove it.
| 17. REMOVE REAR DOOR OUTSIDE STRIPE (for TMMK Made) |
Using a heat light, heat the rear door outside stripe and vehicle body.
| Item | Temperature |
| Vehicle Body and Rear Door Outside Stripe | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the rear door outside stripe to remove it.
| 18. REMOVE REAR DOOR LOWER OUTSIDE STRIPE (for TMMK Made) |
Using a heat light, heat the rear door lower outside stripe and vehicle body.
| Item | Temperature |
| Vehicle Body and Rear Door Lower Outside stripe | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the rear door lower outside stripe to remove it.
| 19. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG (for TMC, TMMR Made) |
![]() |
Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.
| 20. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (for TMC, TMMR Made) |
![]() |
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
w/o Seat Heater System:
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
w/ Seat Heater System:
Disconnect the 2 connectors and remove the rear power window regulator switch assembly with rear door armrest base panel.
| 21. REMOVE REAR ARMREST ASSEMBLY (for TMC, TMMR Made) |
![]() |
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.
| 22. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY (for TMC, TMMR Made) |
![]() |
Put protective tape around the rear door panel.
| *1 | Protective Tape |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 8 clips.
![]() |
Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
| *1 | Reference Boss |
| *2 | Rear Door Inner Glass Weatherstrip |
Disengage the reference boss from the rear door panel.
Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
![]() |
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.
Disconnect the connector.
![]() |
Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 23. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP (for TMC, TMMR Made) |
![]() |
Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
| *1 | Screwdriver |
| 24. REMOVE REAR DOOR SERVICE HOLE COVER (for TMC, TMMR Made) |
![]() |
Disconnect the connector and remove the rear door service hole cover.
| 25. REMOVE REAR DOOR CHECK ASSEMBLY (for TMC, TMMR Made) |
![]() |
Remove the bolt and 2 nuts and rear door check assembly.
| 26. REMOVE REAR DOOR WEATHERSTRIP (for TMC, TMMR Made) |
![]() |
Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.
| 27. REMOVE REAR DOOR GLASS RUN (for TMC, TMMR Made) |
![]() |
Remove the rear door glass run.
| 28. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY (for TMC, TMMR Made) |
![]() |
Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.
| 29. REMOVE REAR DOOR QUARTER WINDOW GLASS (for TMC, TMMR Made) |
![]() |
Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
| 30. REMOVE REAR DOOR GLASS SUB-ASSEMBLY (for TMC, TMMR Made) |
![]() |
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
| 31. REMOVE REAR DOOR FRAME GARNISH (for TMC, TMMR Made) |
![]() |
Disengage the clip and remove the rear door frame garnish.
| 32. REMOVE CURTAIN HOOK (for TMC, TMMR Made) |
| 33. REMOVE REAR DOOR OUTSIDE STRIPE (for TMC, TMMR Made) |
Using a heat light, heat the rear door outside stripe and vehicle body.
| Item | Temperature |
| Vehicle Body and Rear Door Outside Stripe | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the rear door outside stripe to remove it.
| 34. REMOVE REAR DOOR LOWER OUTSIDE STRIPE (for TMC, TMMR Made) |
Using a heat light, heat the rear door lower outside stripe and vehicle body.
| Item | Temperature |
| Vehicle Body and Rear Door Lower Outside stripe | 40 to 60°C (104 to 140°F) |
![]() |
Pull back on one of the ends of the rear door lower outside stripe to remove it.