Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PANEL (for TMC, TMMR Made)

AIR CONDITIONING PANEL (for TMC, TMMR Made) > REMOVAL

for Preparation Click here



1. PRECAUTION (w/ Navigation System)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Navigation System)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE FRONT PANEL GARNISH LH


    B386768
  1. Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.



4. REMOVE FRONT PANEL GARNISH RH


    B386771
  1. Disengage the 3 clips and 8 guides to remove the front panel garnish RH.



5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B281758
  1. Using a moulding remover, pry up on the center instrument cluster finish panel sub-assembly until there is enough of a gap to make it possible to pull on the panel by hand.



    B281757
  1. Pull the center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 7 clips and 2 guides to remove the center instrument cluster finish panel sub-assembly as shown in the illustration.



6. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    B281759
  1. Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 4 clips as shown in the illustration.

  1. Disconnect the connector to remove the No. 2 instrument panel register assembly.



7. REMOVE FRONT CONSOLE UPPER PANEL GARNISH


  1. for Blank Type:



      B386778
    1. Disengage the 2 claws and remove the front console upper panel garnish as shown in the illustration.



  1. for 3 Switch Hole Type:



      B386772
    1. Disengage the 2 claws as shown in the illustration.

    2. Disconnect the each connector to remove the front console upper panel garnish.



8. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio Receiver Type)


    E300907E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape



    E300908
  1. Remove the 4 bolts.



    E300909
  1. Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.



9. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Navigation Receiver Type)


    E300891E01
  1. Apply protective tape to the area shown in the illustration.
    Text in Illustration 
    *a
    Protective Tape



    E300892
  1. Remove the 4 bolts.



    E300893
  1. Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.



10. REMOVE NO. 1 RADIO BRACKET (for Radio Receiver Type)


  1. w/o Navigation System:



      E300894
    1. Remove the 4 screws and No. 1 radio bracket.



  1. w/ Navigation System:



      E300895
    1. Remove the 6 screws and No. 1 radio bracket.



11. REMOVE NO. 2 RADIO BRACKET (for Radio Receiver Type)


  1. w/o Navigation System:



      E300896
    1. Remove the 4 screws and No. 2 radio bracket.



  1. w/ Navigation System:



      E300897
    1. Remove the 6 screws and No. 2 radio bracket.



12. REMOVE NO. 1 RADIO BRACKET (for Navigation Receiver Type)


    E300910
  1. Remove the 4 screws and No. 1 radio bracket.



13. REMOVE NO. 2 RADIO BRACKET (for Navigation Receiver Type)


    E300911
  1. Remove the 4 screws and No. 2 radio bracket.



14. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    E301557
  1. Disengage the 4 clips and remove the air conditioning control assembly.