Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter

for Preparation Click here


DESCRIPTION

  1. The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the radio and display receiver assembly via this circuit.
    The sound signal that has been sent is amplified by the radio and display receiver assembly and then is sent to the speakers.
    If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.

WIRING DIAGRAM


w/ DVD Player

E277819E31


w/o DVD Player

E277819E06


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
  1. Disconnect the I155 radio and display receiver assembly connector.

  1. Disconnect the I204 No. 1 stereo jack adapter assembly connector. (for RHD with DVD Player)

  1. Disconnect the I207 No. 1 stereo jack adapter assembly connector. (for LHD)

  1. Disconnect the I146 No. 1 stereo jack adapter assembly connector. (w/o DVD Player)



    E277839E03
  1. Measure the resistance according to the value(s) in the table below. (for RHD with DVD Player)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-25 (ADPG) - I204-10 (AUXO)
    Always
    Below 1 Ω
    I155-11 (AGND) - I204-12 (AGND)
    Always
    Below 1 Ω
    I155-26 (VAR+) - I204-7 (ARO)
    Always
    Below 1 Ω
    I155-28 (VAL+) - I204-8 (ALO)
    Always
    Below 1 Ω
    I155-27 (VA-) - I204-9 (ASGN)
    Always
    Below 1 Ω
    I155-25 (ADPG) - Body ground
    Always
    10 kΩ or higher
    I155-11 (AGND) - Body ground
    Always
    10 kΩ or higher
    I155-26 (VAR+) - Body ground
    Always
    10 kΩ or higher
    I155-28 (VAL+) - Body ground
    Always
    10 kΩ or higher
    I155-27 (VA-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E277839E04
  1. Measure the resistance according to the value(s) in the table below. (for LHD)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-25 (ADPG) - I207-10 (AUXO)
    Always
    Below 1 Ω
    I155-11 (AGND) - I207-12 (AGND)
    Always
    Below 1 Ω
    I155-26 (VAR+) - I207-7 (ARO)
    Always
    Below 1 Ω
    I155-28 (VAL+) - I207-8 (ALO)
    Always
    Below 1 Ω
    I155-27 (VA-) - I207-9 (ASGN)
    Always
    Below 1 Ω
    I155-25 (ADPG) - Body ground
    Always
    10 kΩ or higher
    I155-11 (AGND) - Body ground
    Always
    10 kΩ or higher
    I155-26 (VAR+) - Body ground
    Always
    10 kΩ or higher
    I155-28 (VAL+) - Body ground
    Always
    10 kΩ or higher
    I155-27 (VA-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E227392E59
  1. Measure the resistance according to the value(s) in the table below. (w/o DVD Player)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-25 (ADPG) - I146-9 (AUXO)
    Always
    Below 1 Ω
    I155-11 (AGND) - I146-10 (AGND)
    Always
    Below 1 Ω
    I155-26 (VAR+) - I146-6 (ARO)
    Always
    Below 1 Ω
    I155-28 (VAL+) - I146-7 (ALO)
    Always
    Below 1 Ω
    I155-27 (VA-) - I146-8 (ASGN)
    Always
    Below 1 Ω
    I155-25 (ADPG) - Body ground
    Always
    10 kΩ or higher
    I155-11 (AGND) - Body ground
    Always
    10 kΩ or higher
    I155-26 (VAR+) - Body ground
    Always
    10 kΩ or higher
    I155-28 (VAL+) - Body ground
    Always
    10 kΩ or higher
    I155-27 (VA-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)