Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Data Signal Circuit between Radio Receiver and Stereo Jack Adapter

for Preparation Click here


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM


for RHD

E268438E40


for LHD

E268438E39


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
  1. Disconnect the I156 radio and display receiver assembly connector. (for RHD)

  1. Disconnect the I205 radio and display receiver assembly connector. (for LHD)

  1. Disconnect the I146 No. 1 stereo jack adapter assembly connector. (for RHD with DVD Player)

  1. Disconnect the I146 No. 1 stereo jack adapter assembly connector. (for LHD)

  1. Disconnect the I146 No. 1 stereo jack adapter assembly connector. (w/o DVD Player)



    E277837E07
  1. Measure the resistance according to the value(s) in the table below. (for RHD with DVD Player)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I205-2 (UDO-) - I204-2 (UDO-)
    Always
    Below 1 Ω
    I205-3 (UDO+) - I204-3 (UDO+)
    Always
    Below 1 Ω
    I205-5 (USG1) - I204-5 (USG1)
    Always
    Below 1 Ω
    I205-2 (UDO-) - Body ground
    Always
    10 kΩ or higher
    I205-3 (UDO+) - Body ground
    Always
    10 kΩ or higher
    I205-5 (USG1) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E277837E08
  1. Measure the resistance according to the value(s) in the table below. (for LHD)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I205-2 (US1-) - I146-2 (UDO-)
    Always
    Below 1 Ω
    I205-3 (US1+) - I146-3 (UDO+)
    Always
    Below 1 Ω
    I205-5 (USG1) - I146-5 (USG1)
    Always
    Below 1 Ω
    I205-2 (US1-) - Body ground
    Always
    10 kΩ or higher
    I205-3 (US1+) - Body ground
    Always
    10 kΩ or higher
    I205-5 (USG1) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



    E289734E26
  1. Measure the resistance according to the value(s) in the table below. (w/o DVD Player)

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I156-2 (UDO-) - I146-2 (UDO-)
    Always
    Below 1 Ω
    I156-3 (UDO+) - I146-3 (UDO+)
    Always
    Below 1 Ω
    I156-5 (USG1) - I146-5 (USG1)
    Always
    Below 1 Ω
    I156-2 (UDO-) - Body ground
    Always
    10 kΩ or higher
    I156-3 (UDO+) - Body ground
    Always
    10 kΩ or higher
    I156-5 (USG1) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)