ROOF HEADLINING (for TMC, TMMR Made) > INSTALLATION |
| 1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof) |
![]() |
Install the 2 clips to the roof headlining assembly.
| *1 | Clip (Black) |
| *2 | Clip (White) |
![]() |
Put the roof headlining assembly into the vehicle through the front door RH.
Engage the 2 clips.

Install the roof headlining assembly with the 2 clips.
Engage the 4 clamps to the front pillar LH.
Engage the 3 clamps to the front pillar RH.
Connect the bracket with the bolt to the front pillar RH.
Engage the 2 clamps and connect the connector to the rear pillar RH.
w/ Television Antenna:
Connect the connector.
w/ Rain Sensor:
Connect the connector.
w/ EC Mirror:
Connect the connector.
| 2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof) |
![]() |
Install the 2 clips to the roof headlining assembly.
| *1 | Clip (Black) |
| *2 | Clip (White) |
![]() |
Put the roof headlining assembly into the vehicle through the front door RH.
Engage the 2 clips and 2 fasteners.

Install the roof headlining assembly with the 2 clips.
Engage the 4 clamps to the front pillar LH.
Engage the 3 clamps to the front pillar RH.
Connect the bracket with the bolt to the front pillar RH.
Engage the 2 clamps and connect the connector to the rear pillar RH.
Connect the connector to the sliding roof drive gear assembly.
w/ Television Antenna:
Connect the connector.
w/ Rain Sensor:
Connect the connector.
w/ EC Mirror:
Connect the connector.
| 3. INSTALL VISOR HOLDER |
![]() |
Engage the 2 claws.
Push in the visor holder as shown in the illustration.
| 4. INSTALL VISOR ASSEMBLY LH |
Install the visor assembly LH with the 2 screws.
| 5. INSTALL VISOR BRACKET COVER (for LH Side) |
![]() |
Engage the 4 claws to install the visor bracket cover.
| 6. INSTALL VISOR ASSEMBLY RH |
| 7. INSTALL VISOR BRACKET COVER (for RH Side) |
| 8. INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof) |
![]() |
Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.
| *1 | Notch |
| *2 | Alignment Mark |
| *3 | Tape |
| 9. INSTALL ASSIST GRIP SUB-ASSEMBLY |
![]() |
Put an assist grip sub-assembly together as shown in the illustration.
![]() |
Engage the 2 clips to install the assist grip sub-assembly.
![]() |
Engage the 4 claws to install the 2 assist grip covers
| 10. INSTALL REAR ASSIST GRIP ASSEMBLY LH |
![]() |
Put an rear assist grip assembly LH together as shown in the illustration.
![]() |
Engage the 2 clips to install the rear assist grip assembly LH.
![]() |
Engage the 4 claws to install the 2 assist grip covers
| 11. INSTALL REAR ASSIST GRIP ASSEMBLY RH |
| 12. INSTALL SPOT LIGHT ASSEMBLY |
Connect the connector.
![]() |
Engage the 4 claws to install the spot light assembly.
| *a | Front |
| 13. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof) |
Connect the connector.
![]() |
Engage the 4 clips to install the roof console box assembly.
| 14. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof) |
Connect the connector.
![]() |
Engage the 4 clips to install the roof console box assembly.
| 15. INSTALL RAIN SENSOR COVER (w/ Rain Sensor) |
Engage the 2 claws to install the rain sensor cover.
| 16. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
except TMMR Made:
Engage the 6 claws and temporarily install the inner rear view mirror stay holder cover.
![]() |
Slide the inner rear view mirror stay holder cover in the direction indicated by arrow shown in the illustration and engage the 2 claws to install the cover.
for TMMR Made:
Engage the 2 claws to temporarily install the inner rear view mirror stay holder cover.
![]() |
Slide the inner rear view mirror stay holder cover in the direction indicated by arrow shown in the illustration to engage the 2 guides and install the cover.
| 17. INSTALL INSTRUMENT PANEL SAFETY PAD |
| 18. INSTALL FRONT SEAT ASSEMBLY LH |
| 19. INSTALL FRONT SEAT ASSEMBLY RH |
| 20. INSTALL ROOF SIDE INNER GARNISH LH |
Engage the guide.
Engage the 5 clips to install the roof side inner garnish LH.
| 21. INSTALL REAR SEAT SIDE GARNISH LH (for Reclining Seat Type) |
Engage the guide, claw and 2 clips.
Install the rear seat side garnish LH with the bolt.
| 22. INSTALL CENTER PILLAR UPPER GARNISH LH |
Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.
Engage the clip.
Install the center pillar upper garnish LH with the 2 screws.
| 23. INSTALL CENTER PILLAR LOWER GARNISH LH |
Engage the 2 claws and 3 clips to install the center pillar lower garnish LH.
| 24. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH |
Install the floor anchor of the front seat outer belt assembly with the bolt.
Check if the ELR locks.
With the belt assembly installed, check that the belt locks when it is pulled out quickly.
| 25. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side) |
Engage the 3 claws to install the lap belt outer anchor cover.
| 26. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| *1 | Alignment Mark (Red) |
| 27. INSTALL REAR DOOR SCUFF PLATE LH |
Engage the 6 claws to install the rear door scuff plate LH.
| 28. INSTALL ROOF SIDE INNER GARNISH RH |
| 29. INSTALL REAR SEAT SIDE GARNISH RH (for Reclining Seat Type) |
| 30. INSTALL CENTER PILLAR UPPER GARNISH RH |
| 31. INSTALL CENTER PILLAR LOWER GARNISH RH |
| 32. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH |
| 33. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side) |
| 34. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
| *1 | Alignment Mark (Blue) |
| 35. INSTALL REAR DOOR SCUFF PLATE RH |
| 36. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
Place the rear side seatback assembly LH in the cabin.
Engage the hook to install the rear side seatback assembly LH with the bolt.
Connect the rear seat outer belt assembly to the rear seat shoulder belt guide LH.
| 37. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type) |
Place the rear side seatback assembly RH in the cabin.
Engage the hook to install the rear side seatback assembly RH with the bolt.
Connect the rear seat outer belt assembly to the rear seat shoulder belt guide RH.
| 38. INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.
| 39. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
Place the rear seat cushion assembly in the cabin.
w/ Seat Heater System:
Engage the 2 clamps.
Connect the connector.
![]() |
Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.
Confirm that the rear seat cushion assembly is firmly installed.
| 40. INSTALL REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type) |
Place the rear seatback assembly LH in the cabin.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
Install the rear seatback assembly LH with the 2 bolts.
![]() |
Engage the fastener as shown in the illustration.
Raise the rear seatback assembly LH.
Connect the rear seat outer belt assembly to the rear seat center shoulder belt guide.
| 41. INSTALL REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type) |
Place the rear seatback assembly RH in the cabin.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
Install the rear seatback assembly RH with the 2 bolts.
![]() |
Engage the fastener as shown in the illustration.
Raise the rear seatback assembly RH.
| 42. INSTALL CENTER SEATBACK ASSEMBLY (for Reclining Seat Type) |
Place the center seatback assembly in the cabin.
Engage the hook.
Install the center seatback assembly with the 2 bolts.
Connect the connector.
| 43. INSTALL REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type) |
Place the rear seatback assembly LH in the cabin.
Install the rear seatback assembly LH with the 2 bolts and 2 nuts.
Engage the 2 hooks to install the cover.
Connect the 2 rear seat belts to the 2 rear seat shoulder belt guides.
w/ Rear Seat Side Airbag:
Connect each connector and clamp to the child restraint anchor bracket sub-assembly LH.
| 44. INSTALL REAR SEATBACK ASSEMBLY RH (for Reclining Seat Type) |
Place the rear seatback assembly RH in the cabin.
Install the rear seatback assembly RH with the 2 bolts and 2 nuts.
Engage the 2 hooks to install the cover.
Connect the rear seat belt to the rear seat shoulder belt guide.
w/ Rear Seat Side Airbag:
Connect each connector and clamp to the child restraint anchor bracket sub-assembly RH.
| 45. INSTALL REAR SEATBACK COVER (for Reclining Seat Type) |
Engage the 4 claws to install the 2 rear seatback covers.
| 46. INSTALL REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.
| 47. INSTALL REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
Place the rear seat cushion assembly in the cabin.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly.
Connect the 2 seat heater connectors.
![]() |
Engage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly to the 2 rear seat cushion lock hooks as shown in the illustration.
Confirm that the rear seat cushion assembly is securely installed.
| 48. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 49. INSTALL REAR SEAT HEADREST ASSEMBLY |
| 50. INSTALL FRONT PILLAR GARNISH LH |
Remove the protective cover.
Make sure that the front pillar garnish clip is not damaged.
![]() ![]() |
Install the front pillar garnish clip to front pillar garnish LH.
| *a | Correct | *b | Incorrect |
Engage the 2 guides as shown in the illustration.
![]() |
Engage the 2 clips to install the front pillar garnish LH.
| 51. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *1 | Alignment Mark (Yellow) |
| 52. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the clip.
| 53. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 10 claws to install the front door scuff plate LH.
| 54. INSTALL FRONT PILLAR GARNISH RH |
| 55. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *1 | Alignment Mark (White) |
| 56. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 57. INSTALL FRONT DOOR SCUFF PLATE RH |
| 58. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 59. INSPECT SRS WARNING LIGHT |