Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD (for TMC, TMMR Made)

RADIO ANTENNA CORD (for TMC, TMMR Made) > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

HINT:
The double-sided tape and tape are not available as supply parts. If these pieces of tape still have enough adhesion to secure the roof headlining and antenna cord, reuse them. If the roof headlining has been replaced with a new one, or if the tape and/or the double-sided tape is no longer sticky, apply new tape following the procedure below.



  1. Apply new double-sided tape.


    E302653E01


    Text in Illustration 
    *A
    w/o Sliding Roof
    *B
    w/ Sliding Roof
    *C
    w/ Television Antenna
    -
    -
    *a
    Double-sided Tape Size
    -
    -
    V100136
    Front
    V100155
    Double-sided Tape

    Double-sided Tape Size 
    Area
    Dimension
    A
    1.0 mm (0.0394 in.)
    B
    10.0 mm (0.394 in.)

    1. Remove the old double-sided tape from the roof headlining assembly.

    2. Prepare the appropriate amount of new double-sided tape.

      HINT:
      Be careful not to touch the adhesive surface.

    3. Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining assembly.

    4. Peel off the release paper from the double-sided tape.



  1. Install the No. 2 antenna cord sub-assembly to the roof headlining assembly from the front of the vehicle.


    E302652E02


    Text in Illustration 
    *A
    w/o Sliding Roof
    *B
    w/ Sliding Roof
    *C
    w/ Television Antenna
    -
    -
    *a
    Adjustment Area
    *b
    Protrusion
    V100136
    Front
    V100155
    Tape
    V100143
    Marking Tape
    -
    -

    HINT:
    Align the taped part of the antenna cable with the protrusion of the roof headlining, and apply tape to secure the cable to the headlining.

  1. Put the pieces of tape back to the positions shown in the illustration in order to secure the antenna cord to the roof headlining assembly.

    HINT:
    1. If the tape is no longer sticky, use other tape, such as packing tape, that has enough adhesion to secure the antenna cord to the roof headlining assembly.
    2. For the right front corner of the roof headlining assembly, align the marking tape on the antenna cord with the protrusion of the roof headlining, and wrap tape around the antenna cord and roof headlining assembly once or twice to securely hold them.
    3. For the right rear corner of the roof headlining assembly, align the marking tape on the antenna cord with the rear edge of the roof headlining, and secure the antenna cord to the roof headlining assembly with tape.
    4. If the entire length of the antenna cord does not fit, adjust the length by tucking in the cord at the area shown in the illustration.



2. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)
w/ Television Antenna:


3. INSTALL ROOF HEADLINING ASSEMBLY
(Click here)


4. INSTALL ANTENNA CORD SUB-ASSEMBLY
  1. for LHD:

    1. Engage the 8 clamps to install the antenna cord sub-assembly.

  1. for RHD:

    1. Engage the 10 clamps to install the antenna cord sub-assembly.



5. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT


    B281908
  1. Engage the 2 claws.

  1. Install the No. 2 side defroster nozzle duct with the screw <D>.



6. INSTALL NO. 3 HEATER TO REGISTER DUCT (for LHD)


    B281907
  1. Install the No. 3 heater to register duct with the 3 screws <D>.

  1. Install the clip.



7. INSTALL HEATER TO REGISTER DUCT ASSEMBLY (for RHD)
  1. Engage the heater to register duct assembly to the ion generator assembly.



    B281904
  1. Install the heater to register duct assembly with the 3 screws <D>.

  1. Install the clip.



8. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
(Click here)