DTC B1622/81 Lost communication with Side Airbag Sensor RH |
DTC B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete |
DTC B1632/81 Lost Communication with Rear Airbag Sensor RH |
DTC B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete |
DTC B1642/81 Lost Communication with Side Satellite Sensor Bus RH |
DTC B1692/81 Lost Communication with Door Side Airbag Sensor RH |
DTC B1693/81 Door Side Airbag Sensor RH Initialization Incomplete |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1622/81 B1623/81 B1632/81 B1633/81 B1642/81 B1692/81 B1693/81 |
|
|

| 1.CHECK CURRENT DTC |
Check for current DTCs (Click here).
| Result | Proceed to |
| Current DTC B1642 or 81 is output. | A |
| Current DTC B1623 or B1633 is output. | B |
| Current DTC B1692 or B1693 is output. | C |
| Current DTC B1622 or B1632 is output. | D |
| Current DTCs B1622, B1623, B1632, B1633, B1642, B1692, B1693 and 81 are not output. | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK CONNECTORS |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.
Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 3.CHECK NO. 2 FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-4 (BBR+) - O11-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 4.CHECK NO. 2 FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-4 (BBR+) - O11-3 (BBR-) | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 5.CHECK NO. 2 FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-4 (BBR+) - Body ground | Engine switch on (IG) | Below 1 V |
| O11-3 (BBR-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 6.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| O11-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 7.CHECK NO. 2 FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-1 (BCR+) - O11-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 8.CHECK NO. 2 FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-1 (BCR+) - O11-2 (BCR-) | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 9.CHECK NO. 2 FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-1 (BCR+) - Body ground | Engine switch on (IG) | Below 1 V |
| O11-2 (BCR-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 10.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| O11-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 11.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (OPEN) |
![]() |
Connect the connectors that link the No. 2 floor wire and front door wire RH.
Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O46-1 (BDR+) - O46-2 (BDR-) | Always | Below 1 Ω |
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *3 | Service Wire |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector (to Door Side Airbag Sensor RH) |
|
| ||||
| OK | |
| 12.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O46-1 (BDR+) - O46-2 (BDR-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 13.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O46-1 (BDR+) - Body ground | Engine switch on (IG) | Below 1 V |
| O46-2 (BDR-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 14.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O46-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| O46-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 15.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Connect the connectors to the side No. 2 airbag sensor assembly RH, door side airbag sensor RH and airbag sensor assembly.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1642 or 81 is output. | A |
| DTC B1647 or 82 is output. | B |
| DTCs B1642, B1647, 81 and 82 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | |
| 16.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH |
![]() |
Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1642 or 81 is output. | A |
| DTC B1647 or 82 is output. | B |
| DTCs B1642, B1647, 81 and 82 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
|
| ||||
|
| ||||
| A | |
| 17.CHECK DOOR SIDE AIRBAG SENSOR RH |
![]() |
Interchange the door side airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1642 or 81 is output. | A |
| DTC B1647 or 82 is output. | B |
| DTCs B1642, B1647, 81 and 82 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors.
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
|
| ||||
|
| ||||
| A | ||
| ||
| 18.CHECK HISTORY DTC |
Check for history DTCs (Click here).
| Result | Proceed to |
| History DTCs B1622 and B1632 are not output. | A |
| History DTC B1622 is output. | B |
| History DTC B1632 is output. | C |
|
| ||||
|
| ||||
| A | |
| 19.CHECK CURRENT DTC |
Check for current DTCs (Click here).
| Result | Proceed to |
| Current DTC B1623 is output. | A |
| Current DTC B1633 is output. | B |
|
| ||||
| A | |
| 20.CHECK CONNECTORS |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.
Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 21.CHECK NO. 2 FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-4 (BBR+) - O11-3 (BBR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 22.CHECK NO. 2 FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-4 (BBR+) - O11-3 (BBR-) | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 23.CHECK NO. 2 FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-4 (BBR+) - Body ground | Engine switch on (IG) | Below 1 V |
| O11-3 (BBR-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 24.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-4 (BBR+) - Body ground | Always | 1 MΩ or higher |
| O11-3 (BBR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 25.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Connect the connector to the airbag sensor assembly.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1623 is output. | A |
| DTC B1628 is output. | B |
| DTCs B1623 and B1628 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | ||
| ||
| 26.CHECK CONNECTORS |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 27.CHECK NO. 2 FLOOR WIRE (OPEN) |
![]() |
Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-1 (BCR+) - O11-2 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector C.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 28.CHECK NO. 2 FLOOR WIRE (SHORT) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-1 (BCR+) - O11-2 (BCR-) | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 29.CHECK NO. 2 FLOOR WIRE (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-1 (BCR+) - Body ground | Engine switch on (IG) | Below 1 V |
| O11-2 (BCR-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 30.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O11-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| O11-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Side No. 2 Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Side Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 31.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Connect the connector to the side No. 2 airbag sensor assembly RH.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1633 is output. | A |
| DTC B1638 is output. | B |
| DTCs B1633 and B1638 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | |
| 32.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH |
![]() |
Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1633 is output. | A |
| DTC B1638 is output. | B |
| DTCs B1633 and B1638 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
|
| ||||
|
| ||||
| A | ||
| ||
| 33.CHECK CONNECTORS |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.
Disconnect the connectors from the side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.
Check that the terminals of the connectors are not damaged.
|
| ||||
| OK | |
| 34.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (OPEN) |
![]() |
Connect the connectors that link the No. 2 floor wire and front door wire RH.
Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O46-1 (BDR+) - O46-2 (BDR-) | Always | Below 1 Ω |
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *3 | Service Wire |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
| *b | Front view of wire harness connector (to Door Side Airbag Sensor RH) |
|
| ||||
| OK | |
| 35.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT) |
![]() |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O46-1 (BDR+) - O46-2 (BDR-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 36.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO B+) |
![]() |
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O46-1 (BDR+) - Body ground | Engine switch on (IG) | Below 1 V |
| O46-2 (BDR-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 37.CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O46-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| O46-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *a | Front view of wire harness connector (to Side No. 2 Airbag Sensor Assembly RH) |
|
| ||||
| OK | |
| 38.CHECK DOOR SIDE AIRBAG SENSOR RH |
![]() |
Connect the connectors to the side No. 2 airbag sensor assembly RH.
Interchange the door side airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1692 or B1693 is output. | A |
| DTC B1697 or B1698 is output. | B |
| DTCs B1692, B1693, B1697 and B1698 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors.
| *1 | Door Side Airbag Sensor LH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
|
| ||||
|
| ||||
| A | |
| 39.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH |
![]() |
Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1692 or B1693 is output. | A |
| DTC B1697 or B1698 is output. | B |
| DTCs B1692, B1693, B1697 and B1698 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
|
| ||||
|
| ||||
| A | ||
| ||
| 40.CHECK CURRENT DTC |
Check for current DTCs (Click here).
| Result | Proceed to |
| Current DTC B1622 is output. | A |
| Current DTC B1632 is output. | B |
Turn the engine switch off.
|
| ||||
| A | |
| 41.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH |
![]() |
Disconnect the cable from the negative (-) battery terminal.
Interchange the side airbag sensor assembly RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1622 is output. | A |
| DTC B1627 is output. | B |
| DTCs B1622 and B1627 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
|
| ||||
|
| ||||
| A | ||
| ||
| 42.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH |
![]() |
Disconnect the cable from the negative (-) battery terminal.
Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| Result | Proceed to |
| DTC B1632 is output. | A |
| DTC B1637 is output. | B |
| DTCs B1632 and B1637 are not output. | C |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.
| *1 | Side No. 2 Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
|
| ||||
|
| ||||
| A | ||
| ||
| 43.CHECK FRONT DOOR WIRE RH (OPEN) |
![]() |
Disconnect the front door wire RH connector from the No. 2 floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JO1-1 (BDR+) - JO1-2 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | No. 2 Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector (to No. 2 Floor Wire) |
| *b | Front view of wire harness connector (to Door Side Airbag Sensor RH) |
|
| ||||
| OK | ||
| ||
| 44.CHECK FRONT DOOR WIRE RH (SHORT) |
![]() |
Disconnect the front door wire RH connector from the No. 2 floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JO1-1 (BDR+) - JO1-2 (BDR-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to No. 2 Floor Wire) |
|
| ||||
| OK | ||
| ||
| 45.CHECK FRONT DOOR WIRE RH (SHORT TO B+) |
![]() |
Disconnect the front door wire RH connector from the No. 2 floor wire.
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JO1-1 (BDR+) - Body ground | Engine switch on (IG) | Below 1 V |
| JO1-2 (BDR-) - Body ground | Engine switch on (IG) | Below 1 V |
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to No. 2 Floor Wire) |
|
| ||||
| OK | ||
| ||
| 46.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND) |
![]() |
Disconnect the front door wire RH connector from the No. 2 floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| JO1-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| JO1-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | Side No. 2 Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to No. 2 Floor Wire) |
|
| ||||
| OK | ||
| ||