Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows)

DTC    B2311    Power Window Motor Malfunction

for Preparation Click here


DESCRIPTION

The power window regulator motor assembly is operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly. The power window regulator motor assembly has motor, regulator and ECU functions.
This DTC is output when the power window regulator motor assembly has a malfunction, or the ECU built into the power window regulator motor assembly determines that the fully closed window position has deviated approximately 20 mm (0.787 in.) or more from the normal position.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door)) 
DTC No.
DTC Detection Condition
Trouble Area
B2311
  1. Either condition is met:
    1. Power window regulator motor assembly malfunctions
    2. When ECU in power window regulator motor assembly determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position
  1. Power window regulator motor assembly (for driver door)
  2. Incorrect installation of power window components
  3. Overheated power window regulator motor assembly

P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Door)) 
DTC No.
DTC Detection Condition
Trouble Area
B2311
  1. Either condition is met:
    1. Power window regulator motor assembly malfunctions
    2. When ECU in power window regulator motor assembly determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position
  1. Power window regulator motor assembly (for front passenger door)
  2. Incorrect installation of power window components
  3. Overheated power window regulator motor assembly

RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Door)) 
DTC No.
DTC Detection Condition
Trouble Area
B2311
  1. Either condition is met:
    1. Power window regulator motor assembly malfunctions
    2. When ECU in power window regulator motor assembly determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position
  1. Power window regulator motor assembly (for rear LH door)
  2. Incorrect installation of power window components
  3. Overheated power window regulator motor assembly

RR-Door Motor (Power Window Regulator Motor Assembly (for Rear RH Door)) 
DTC No.
DTC Detection Condition
Trouble Area
B2311
  1. Either condition is met:
    1. Power window regulator motor assembly malfunctions
    2. When ECU in power window regulator motor assembly determines that fully closed window position has deviated approx. 20 mm (0.787 in.) or more from normal position
  1. Power window regulator motor assembly (for rear RH door)
  2. Incorrect installation of power window components
  3. Overheated power window regulator motor assembly

INSPECTION PROCEDURE

NOTICE:
  1. DTC B2311 can be stored in each power window regulator motor assembly (power window ECU).
  2. If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (Click here).
  3. If a power window regulator motor assembly and door window regulator sub-assembly have been removed and installed, or if a power window regulator motor assembly was reused when a door glass or door glass run was replaced, initialize the power window control system (Click here).

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (APPLICABLE LOCATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / (desired system) / Active Test.

    HINT:
    Perform the Active Test for the power window regulator motor assembly that has DTC B2311 stored in its ECU.

  1. Perform the Active Test according to the display on the intelligent tester.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


    D-Door Motor (Power Window Regulator Motor Assembly (for Driver Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    P-Door Motor (Power Window Regulator Motor Assembly (for Front Passenger Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    RR-Door Motor (Power Window Regulator Motor Assembly (for Rear RH Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    OK:
    Each power window motor operates.

    Result:
    Result
    Proceed to
    OK
    A
    NG (Driver door power window)
    B
    NG (Front passenger door power window)
    B
    NG (Rear LH door power window)
    C
    NG (Rear RH door power window)
    C



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR) (Click here)

C
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR) (Click here)
A


2.PERFORM INITIALIZATION (APPLICABLE LOCATION)
  1. Initialize the power window regulator motor assembly (Click here).

    HINT:
    Initialize the power window regulator motor assembly that has DTC B2311 stored in its ECU.


NEXT


3.CHECK POWER WINDOW CONTROL SYSTEM (APPLICABLE LOCATION)
  1. Check that the power window operates normally by opening and closing the window (Click here).

    HINT:
    Check the power window operation of the window where DTC B2311 has been stored.

    OK:
    Each power window operates normally.

    Result:
    Result
    Proceed to
    OK
    A
    NG (Driver door power window)
    B
    NG (Front passenger door power window)
    B
    NG (Rear LH door power window)
    C
    NG (Rear RH door power window)
    C



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR) (Click here)

C
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR) (Click here)
A


4.CHECK WHETHER PARTS HAVE BEEN INSTALLED CORRECTLY
  1. Check that the power window components are installed correctly.

    OK:
    Power window components are installed correctly.



NG
INSTALL PARTS CORRECTLY
OK


5.CHECK DTC OUTPUT
  1. Turn the ignition switch off.

  1. Wait for at least 10 seconds, and then turn the ignition switch to ON.

  1. Check for DTCs (Click here).

    OK:
    B2311 output does not recur.

Result:
Result
Proceed to
OK
A
NG (Driver door power window)
B
NG (Front passenger door power window)
B
NG (Rear LH door power window)
C
NG (Rear RH door power window)
C



B
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR OR FRONT PASSENGER DOOR) (Click here)

C
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR OR REAR RH DOOR) (Click here)
A

END