Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U1115    Lost Communication with Tilt and Telescopic Module

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
U1115
No communication from the multiplex tilt and telescopic ECU continues.
  1. Multiplex tilt and telescopic ECU branch line or connector
  2. Power source circuit of multiplex tilt and telescopic ECU
  3. Multiplex tilt and telescopic ECU ground circuit
  4. Multiplex tilt and telescopic ECU

HINT:
This diagnosis procedure is for when DTC U1115 is output by the main body ECU (multiplex network body ECU) (GTS display: Main Body).


WIRING DIAGRAM


C253651E04


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON and wait at least 10 seconds.
  6. After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.RECONFIRM DTC OUTPUT
  1. Reconfirm DTCs.

    HINT:
    If DTC U1002 is output from Main Body of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in the sub bus 1.

    Result:
    Result
    Proceed to
    DTC U1002 is not output from main body ECU (multiplex network body ECU) (GTS display: Main Body)
    A
    DTC U1002 is output from main body ECU (multiplex network body ECU) (GTS display: Main Body)
    B



B
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC (Click here)
A


2.CHECK FOR OPEN IN SUB BUS 1 LINES (MULTIPLEX TILT AND TELESCOPIC ECU BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C240239E57
  1. Disconnect the I15 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I15-3 (CANP) - I15-11 (CANN)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU)
OK


3.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    C240239E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I15-1 (GND) - Body ground
    Cable disconnected from negative (-) battery terminal
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
OK


4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
  1. Connect the cable to the negative (-) battery terminal.



    C240239E59
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I15-9 (ECUB) - Body ground
    Always
    11 to 14 V
    I15-10 (IG) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)