Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

NAVIGATION SYSTEM (for Navigation Receiver Type) > Microphone Circuit between Microphone and Navigation Receiver Assembly

for Preparation Click here


DESCRIPTION


  1. The navigation receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
    Using this circuit, the navigation receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM


E300235E04


INSPECTION PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)


    E268457
  1. Enter the "Microphone Check" screen.
    Refer to Check Microphone in Operation Check (Click here).

  1. When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

  1. Push the recording switch and perform voice recording.

    HINT:
    1. Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
    2. Voice can be recorded for up to 5 seconds.

  1. Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.

    OK:
    All check results are normal.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the I67 navigation receiver assembly connector.

  1. Disconnect the S7 roof console box assembly (telephone microphone assembly) connector (for TMC Made).
    Disconnect the S14 roof console box assembly (telephone microphone assembly) connector (for TMMK Made).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-4 (MACC) - S7-14 (MACC)*1
    I67-4 (MACC) - S14-14 (MACC)*2
    Always
    Below 1 Ω
    I67-5 (MIN+) - S7-13 (MCO+)*1
    I67-5 (MIN+) - S14-13 (MCO+)*2
    Always
    Below 1 Ω
    I67-19 (MIN-) - S7-12 (MCO-)*1
    I67-19 (MIN-) - S14-12 (MCO-)*2
    Always
    Below 1 Ω
    I67-6 (SNS2) - S7-15 (SNS2)*1
    I67-6 (SNS2) - S14-15 (SNS2)*2
    Always
    Below 1 Ω
    I67-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    I67-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    I67-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    I67-18 (SGND) - Body ground
    Always
    10 kΩ or higher
    I67-6 (SNS2) - Body ground
    Always
    10 kΩ or higher

    1. *1: for TMC Made
      *2: for TMMK Made



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT NAVIGATION RECEIVER ASSEMBLY


    E289735E11
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I67-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I67-18 (SGND) - Body ground
    Always
    Below 1 Ω
    I67-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC Made)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A


4.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Remove the roof console box assembly (telephone microphone assembly) (for TMMK Made) (Click here).
    Remove the roof console box assembly (telephone microphone assembly) (for TMC Made) (Click here).



    E187117E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    15 (SNS2) - 12 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC Made)
    C



B
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (for TMMK Made) (Click here)

C
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (for TMC Made) (Click here)
A


5.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Turn the ignition switch to ACC.



    E187122E57
  1. Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S7 roof console box assembly (telephone microphone assembly) connector (for TMC Made).
    Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S14 roof console box assembly (telephone microphone assembly) connector (for TMMK Made).

  1. Check the waveform of the roof console box assembly (telephone microphone assembly) using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output.
    A
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output.
    (for TMMK Made)
    B
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output.
    (for TMC Made)
    C

    Text in Illustration 
    *A
    for TMC Made
    *B
    for TMMK Made
    *a
    Component with harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))



B
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (for TMMK Made) (Click here)

C
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (for TMC Made) (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)