Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > Power Mirrors do not Return to Memorized Position

for Preparation Click here


SYSTEM DESCRIPTION

If either the M1 or M2 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the seat memory switch status and sends the switch signal to the main body ECU (multiplex network body ECU) via CAN communication. The main body ECU (multiplex network body ECU) sends back reproduction signals to each outer mirror control ECU assembly via CAN communication. When receiving the reproduction signals, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly, to adjust the mirror surface to the stored position.

WIRING DIAGRAM


B296500E18


INSPECTION PROCEDURE

NOTICE:
The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly (Click here).

1.CHECK SEAT MEMORY SWITCH FUNCTION
  1. When any seat memory switch (M1 or M2 switch) is pressed, check that the driver seat moves to the memorized position.

    OK:
    The driver seat moves to the memorized position.



NG
GO TO POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position) (Click here)
OK


2.CHECK POWER MIRROR CONTROL FUNCTION (ELECTRICAL REMOTE CONTROL MIRROR FUNCTION)
  1. Check the electrical remote control mirror function (Click here).

    OK:
    Electrical remote control mirror function is normal.



NG
GO TO OTHER DIAGNOSIS PROCEDURE (Click here)
OK


3.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Mirror L or Mirror R / Data List.

  1. Read the Data List according to the display on the GTS.

    Mirror L / Mirror R 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror Memory No. 1
    Mirror position memorized in seat memory switch M1 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    Mirror Memory No. 2
    Mirror position memorized in seat memory switch M2 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    -
    Mirror Memory No. 3*
    Mirror position memorized in seat memory switch M3 / ON or OFF
    ON: Memorized
    OFF: Not memorized
    Not applicable

    1. *: Although the item is displayed on the GTS, it is not applicable to this vehicle.

    OK:
    ON (Memorized) appears on the screen.



NG
GO TO OTHER DIAGNOSIS PROCEDURE (Power Mirror Surface Position is not Memorized) (Click here)
OK


4.CHECK MEMORY AND REACTIVATION FUNCTION


    B293945E06
  1. Turn the engine switch on (IG).

  1. Using the outer mirror switch assembly, turn the mirror surface to the fully left position.

  1. Press the M1 switch while the SET switch is being pressed.

  1. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

  1. Using the outer mirror switch assembly, turn the mirror surface to the fully right position.

  1. Press the M1 switch.

  1. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

    Result:
    Result
    Proceed to
    Memory and reactivation functions on both mirrors are not normal
    A
    Memory and reactivation functions on driver door mirror are not normal
    B
    Memory and reactivation functions on front passenger door mirror are not normal
    C

    Text in Illustration 
    *a
    Turn to Left Fully



B
Go to step 5

C
Go to step 7
A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

5.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)
  1. Replace the outer rear view mirror assembly (driver door) (Click here).


NEXT


6.CHECK MEMORY AND REACTIVATION FUNCTION


    B293945E06
  1. Turn the engine switch on (IG).

  1. Using the outer mirror switch assembly, turn the mirror surface to the fully left position.

  1. Press the M1 switch while the SET switch is being pressed.

  1. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

  1. Using the outer mirror switch assembly, turn the mirror surface to the fully right position.

  1. Press the M1 switch.

  1. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

    OK:
    Memory and reactivation function is normal.

    Text in Illustration 
    *a
    Turn to Left Fully



NG
REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) (Click here)
OK

END (OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) WAS DEFECTIVE) 

7.REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)
  1. Replace the outer rear view mirror assembly (front passenger door) (Click here).


NEXT


8.CHECK MEMORY AND REACTIVATION FUNCTION


    B293945E01
  1. Turn the engine switch on (IG).

  1. Using the outer mirror switch assembly, turn the mirror surface to the fully left position.

  1. Press the M1 switch while the SET switch is being pressed.

  1. Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.

  1. Using the outer mirror switch assembly, turn the mirror surface to the fully right position.

  1. Press the M1 switch.

  1. Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

    OK:
    Memory and reactivation function is normal.

    Text in Illustration 
    *a
    Turn to Left Fully



NG
REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) (Click here)
OK

END (OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) WAS DEFECTIVE)