Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) > Power Seat Position is not Memorized

for Preparation Click here


DESCRIPTION

The main body ECU (multiplex network body ECU) receives seat memory switch signals from the outer mirror control ECU assembly LH via CAN communication. If the seat memory SET switch is being pressed when one of the M1 or M2 switches is pressed, or if one of the M1 or M2 switches is pressed within 3 seconds of pressing the seat memory SET switch, the main body ECU (multiplex network body ECU) sends a memory request signal to the front power seat switch LH (w/ Memory). After receiving the request signal, the front power seat switch LH (w/ Memory) memorizes the location data of each motor.

WIRING DIAGRAM


B293826E22


INSPECTION PROCEDURE

NOTICE:
  1. The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.
  2. If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.
  3. The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).

1.CHECK FRONT POWER SEAT CONTROL SYSTEM
  1. Check that each function of the power seat operates normally by using the power seat switch (Click here).

    OK:
    Each function of the power seat operates normally using the power seat switch.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


2.READ VALUE USING GTS (SEAT MEMORY SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body / Mirror L / Data List

  1. Read the Data List according to the display on the GTS.

    Mirror L (Outer Mirror Control ECU Assembly LH) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SET Switch
    SET switch signal / ON or OFF
    ON: SET switch on
    OFF: SET switch off
    -
    M1 Switch
    M1 switch signal / ON or OFF
    ON: M1 switch on
    OFF: M1 switch off
    -
    M2 Switch
    M2 switch signal / ON or OFF
    ON: M2 switch on
    OFF: M2 switch off
    -

    OK:
    ON or OFF is displayed on the GTS according to the table above.



NG
Go to step 8
OK


3.PERFORM ACTIVE TEST USING GTS (BUZZER)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body / Driver Seat / Data List.

  1. Read the Data List according to the display on the GTS.

    Driver Seat (Front Power Seat Switch LH (w/ Memory)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Buzzer
    Buzzer operation
    OFF/ON
    -

OK:
Buzzer sounds normally.



NG
REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY) (Click here)
OK


4.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH
  1. Replace the outer mirror control ECU assembly LH (Click here).


NEXT


5.CHECK SEAT POSITION MEMORY FUNCTION
  1. Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored (Click here).

    NOTICE:
    1. The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.
    2. If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

    OK:
    Seat position memory function operates normally.



NG
Go to step 6
OK

END (OUTER MIRROR CONTROL ECU LH WAS DEFECTIVE) 

6.REPLACE FRONT POWER SEAT SWITCH LH (W/ MEMORY)
  1. Replace the front power seat switch LH (w/ Memory) (Click here).


NEXT


7.CHECK SEAT POSITION MEMORY FUNCTION
  1. Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored (Click here).

    NOTICE:
    1. The seat position will not be recorded if the SET switch and 2 of the seat memory switches are pressed simultaneously.
    2. If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.

    OK:
    Seat position memory function operates normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (FRONT POWER SEAT SWITCH LH (W/ MEMORY) WAS DEFECTIVE) 

8.INSPECT SEAT MEMORY SWITCH


    B295109E01
  1. Remove the seat memory switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 1
    SET switch is pressed
    Below 1 Ω
    4 - 1
    M1 switch is pressed
    Below 1 Ω
    3 - 1
    M2 switch is pressed
    Below 1 Ω
    2 - 1
    SET switch is not pressed
    10 kΩ or higher
    4 - 1
    M1 switch is not pressed
    10 kΩ or higher
    3 - 1
    M2 switch is not pressed
    10 kΩ or higher

    Text in Illustration 
    *1
    M1 Switch
    *2
    M2 Switch
    *3
    SET Switch
    *a
    Component without harness connected
    (Seat Memory Switch)



NG
REPLACE SEAT MEMORY SWITCH (Click here)
OK


9.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - SEAT MEMORY SWITCH)
  1. Disconnect the K12 outer mirror control ECU assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K13-2 (MRY) - K12-1 (MM)
    Always
    Below 1 Ω
    K13-4 (M1) - K12-2 (M1)
    Always
    Below 1 Ω
    K13-3 (M2) - K12-3 (M2)
    Always
    Below 1 Ω
    K13-1 (E) - K12-4 (MSWE)
    Always
    Below 1 Ω
    K12-7 (GND) - Body ground
    Always
    Below 1 Ω
    K12-1 (MM) - Body ground
    Always
    10 kΩ or higher
    K12-2 (M1) - Body ground
    Always
    10 kΩ or higher
    K12-3 (M2) - Body ground
    Always
    10 kΩ or higher
    K12-4 (MSWE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH (Click here)