EXHAUST MANIFOLD > INSTALLATION |
| 1. INSTALL STUD BOLT |
![]() |
Using an E8 "TORX" socket wrench, install the stud bolt to the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
| 2. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR |
Install the No. 2 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 2 bolts.
| 3. INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR |
Install the No. 1 manifold converter insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 3 bolts.
| 4. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst) |
Install a new exhaust manifold gasket to the cylinder head sub-assembly.
Temporarily install the exhaust manifold converter sub-assembly (TWC: Front Catalyst) to the cylinder head sub-assembly with the 5 nuts.
Install 2 new EGR cooler gaskets to the EGR pipe connector.
Temporarily install the EGR pipe connector to the exhaust manifold converter sub-assembly (TWC: Front Catalyst), EGR cooler assembly and cylinder block sub-assembly with the 4 bolts and nut.
![]() |
Tighten the 5 nuts in the order shown in the illustration.
![]() |
Tighten the 4 bolts and nut.
| *a | Bolt (A) |
| *b | Bolt (B) |
![]() | Bolt |
![]() | Nut |
| 5. INSTALL NO. 2 MANIFOLD STAY |
Install the No. 2 manifold stay to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly with the bolt and nut.
| 6. INSTALL MANIFOLD STAY |
Install the manifold stay to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly with the bolt and nut.
| 7. INSTALL AIR FUEL RATIO SENSOR |
![]() |
Using SST, install the air fuel ratio sensor to the exhaust manifold.
| *a | Torque Wrench Fulcrum Length |
Connect the air fuel ratio sensor connector.
Engage the 3 wire harness clamps.
| 8. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
Install the No. 1 exhaust manifold heat insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 4 bolts.
| 9. INSTALL INLET AIR CLEANER ASSEMBLY |
Install the inlet air cleaner assembly with the 2 bolts.
| 10. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) |
![]() |
Using a vernier caliper, measure the free length of the 2 compression springs.
| Minimum Free Length | 40.5 mm (1.59 in.) |
Temporarily install a new exhaust pipe gasket to the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
![]() |
Using a plastic hammer and wooden block, tap in the exhaust pipe gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst).
| *1 | Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) |
| *2 | Exhaust Pipe Gasket |
| *a | Wooden Block |
Install a new exhaust pipe gasket to the front exhaust pipe assembly (TWC: Rear Catalyst).
Connect the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust pipe support.
Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and center exhaust pipe assembly with the 2 compression springs, 2 bolts and 2 nuts.
![]() |
| *1 | Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) |
| *2 | Front Exhaust Pipe Assembly (TWC: Rear Catalyst) |
| *3 | Exhaust Pipe Gasket |
| *a | Space between Flanges: 8.5 mm (0.335 in.) |
Connect the heated oxygen sensor connector.
| 11. INSPECT FOR EXHAUST GAS LEAK |
Perform Inspection After Repair after repairing an exhaust gas leak (Click here).
| 12. INSTALL ENGINE UNDER COVER LH |
Install the engine under cover LH with the 3 screws and 2 clips.
| 13. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
Install the front wheel opening extension pad LH with the 3 screws.
| 14. INSTALL ENGINE UNDER COVER RH |
Install the engine under cover RH with the 3 screws and 3 clips.
| 15. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |
Install the front wheel opening extension pad RH with the 3 screws.