Home › Engine / Hybrid System · 2AR-FE › COOLING › COOLING FAN SYSTEM

COOLING FAN SYSTEM > Cooling Fan Circuit

for Preparation Click here


DESCRIPTION

The ECM monitors engine coolant temperature, the air conditioning switch, the air conditioning refrigerant pressure and engine speed. It also sends the FANL and FANH signals to the engine room junction block assembly to operate the cooling fan motor and No. 2 cooling fan motor.
The ECM switches the cooling fan motor and No. 2 cooling fan motor circuits from a series (low speed rotation) to parallel (high speed rotation) connection by changing the FANH signal, thereby controlling the 2 levels of fan speed.

Input signal
FANL
OFF
ON
ON
FANH
OFF
OFF
ON
Condition
Cooling fan motor
OFF
ON (Series connection (Low speed rotation))
ON (Parallel connection (High speed rotation))
No. 2 cooling fan motor
OFF
ON (Series connection (Low speed rotation))
ON (Parallel connection (High speed rotation))

A258352E01


WIRING DIAGRAM


A267824E02


A260495E02


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE ELECTRIC COOLING FAN)

HINT:
If cooling fan speed does not change, proceed to the next step.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Electric Cooling Fan.

  1. Check the operation of the cooling fans using the intelligent tester.

    OK:

    Tester Operation
    Fan Operation
    ON
    Cooling fan operates
    OFF
    Cooling fan stops


    Result:

    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 3
A


2.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the ECM connector.

  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

  1. Disconnect the engine room junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A25-5 (FANL) - 1F-17 (FANL)
    Always
    Below 1 Ω
    A25-6 (FANH) - 1F-9 (FANH)
    Always
    Below 1 Ω
    A25-5 (FANL) or 1F-17 (FANL) - Body ground
    Always
    10 kΩ or higher
    A25-6 (FANH) or 1F-9 (FANH) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
OK


3.INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (SIGNAL READING CHECK)
  1. Using a voltmeter, check the signal reading of the engine room junction block assembly .

    OK:
    Output signal reading is normal.



NG
INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK)
OK


4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY POWER SOURCE)


    A259163E01
  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    (BATT) - Body ground
    Ignition switch off
    11 to 14 V
    (ALT) - Body ground
    Ignition switch off
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block and Junction Block Assembly
    *2
    ALT
    *3
    BATT



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - BATTERY)
OK


5.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - BODY GROUND)
  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

  1. Disconnect the engine room junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1F-3 (GND1) - Body ground
    Always
    Below 1 Ω
    1G-4 (GND2) - Body ground
    Always
    Below 1 Ω

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - BODY GROUND)
OK


6.CHECK HARNESS AND CONNECTOR (FAN RELAY POWER SOURCE)


    A259164E01
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 (FAN relay) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block and Junction Block Assembly
    *2
    FAN Relay



NG
Go to step 18
OK


7.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - FAN RELAY)
  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

  1. Disconnect the engine room junction block assembly connector.

  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1F-15 (IGN) - 1 (FAN relay)
    Always
    Below 1 Ω
    1F-15 (IGN) or 1 (FAN relay) - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
OK


8.INSPECT FAN RELAY
  1. Inspect the FAN relay (Click here).



NG
REPLACE FAN RELAY
OK


9.CHECK HARNESS AND CONNECTOR (FAN RELAY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

  1. Disconnect the engine room junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    2 (FAN relay) - 1F-8 (FN2S)
    Always
    Below 1 Ω
    2 (FAN relay) or 1F-8 (FN2S) - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
OK


10.CHECK HARNESS AND CONNECTOR (FAN RELAY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    4 (FAN relay) - 1M-2 (FAN2)
    Always
    Below 1 Ω
    4 (FAN relay) or 1M-2 (FAN2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
OK


11.CHECK HARNESS AND CONNECTOR (FAN RELAY - BODY GROUND)
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    5 (FAN relay) - Body ground
    Always
    Below 1 Ω

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - BODY GROUND)
OK


12.INSPECT NO. 2 COOLING FAN MOTOR
  1. Inspect the No. 2 cooling fan motor (Click here).



NG
REPLACE NO. 2 COOLING FAN MOTOR (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (FAN RELAY - NO. 2 COOLING FAN MOTOR)
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Disconnect the No. 2 cooling fan motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3 (FAN relay) - A8-1 (L)
    Always
    Below 1 Ω
    3 (FAN relay) or A8-1 (L) - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - NO. 2 COOLING FAN MOTOR)
OK


14.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the No. 2 cooling fan motor connector.

  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A8-2 (B) - 1M-3 (CFAN)
    Always
    Below 1 Ω
    A8-2 (B) or 1M-3 (CFAN) - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 2 COOLING FAN MOTOR - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
OK


15.INSPECT COOLING FAN MOTOR
  1. Inspect the cooling fan motor (Click here).



NG
REPLACE COOLING FAN MOTOR (Click here)
OK


16.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - COOLING FAN MOTOR)
  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

  1. Disconnect the cooling fan motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1M-1 (RFAN) - A7-2
    Always
    Below 1 Ω
    1M-1 (RFAN) or A7-2 - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - COOLING FAN MOTOR)
OK


17.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
  1. Disconnect the cooling fan motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A7-1 - Body ground
    Always
    Below 1 Ω

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

18.CHECK HARNESS AND CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Remove the FAN relay from the engine room relay block and junction block assembly.

  1. Disconnect the instrument panel junction block assembly connector.

  1. Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

  1. Disconnect the engine room junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1 (FAN relay) - 3D-36
    Always
    Below 1 Ω
    1 (FAN relay) or 3D-36 - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FAN RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
OK


19.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)


    A263496E03
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (RHD):
    Tester Connection
    Condition
    Specified Condition
    3F-1 - 3D-36
    Battery voltage is not applied between terminals 3A-27 and 3B-7
    10 kΩ or higher
    3F-1 - 3D-36
    Battery voltage is applied between terminals 3A-27 and 3B-7
    Below 1 Ω

    Standard Resistance (LHD):
    Tester Connection
    Condition
    Specified Condition
    3E-1 - 3D-36
    Battery voltage is not applied between terminals 3A-27 and 3B-7
    10 kΩ or higher
    3E-1 - 3D-36
    Battery voltage is applied between terminals 3A-27 and 3B-7
    Below 1 Ω

    Text in Illustration 
    *1
    Instrument Panel Junction Block Assembly



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 2 RELAY)
OK


20.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY POWER SOURCE)


    A258037E03
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (RHD):
    Tester Connection
    Condition
    Specified Condition
    3F-1 - Body ground
    Always
    11 to 14 V

    Standard Voltage (LHD):
    Tester Connection
    Condition
    Specified Condition
    3E-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Instrument Panel Junction Block Assembly)
    *A
    for LHD
    *B
    for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY)
OK


21.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
  1. Disconnect the instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3B-7 - Body ground
    Always
    Below 1 Ω


    Result:

    Result
    Proceed to
    OK (w/o Smart Entry and Start System)
    A
    OK (w/ Smart Entry and Start System)
    B
    NG
    C

    HINT:
    Make sure that there are no short circuits to the battery.



B
Go to step 24

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
A


22.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)
  1. Disconnect the instrument panel junction block assembly connector.

  1. Disconnect the ignition or starter switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3A-27 - I36-1 (IG1)
    Always
    Below 1 Ω
    3A-27 or I36-1 (IG1) - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)
OK


23.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
  1. Inspect the ignition or starter switch assembly (Click here).



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - BATTERY) 

24.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Disconnect the instrument panel junction block assembly connector.

  1. Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    3A-27 - I78-6 (IG1D)
    Always
    Below 1 Ω
    3A-27 or I78-6 (IG1D) - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
OK

CHECK SMART ENTRY AND START SYSTEM (Click here)