Home › Engine / Hybrid System · 2AR-FE › ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).
  1. *1: w/o smart entry and start system
  2. *2: w/ smart entry and start system or Push-Button Start

WIRING DIAGRAM


A266832E14


A266833E07


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

1.CHECK WHETHER ENGINE CAN BE CRANKED
  1. Check if the engine can be cranked.

    Result 
    Result
    Proceed to
    Engine cannot be cranked
    A
    Engine can be cranked
    B



B
Go to step 12
A


2.READ VALUE USING GTS (STARTER SIGNAL)
  1. Connect the GTS to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

    OK 
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
Go to step 13
OK


3.INSPECT RELAY (ST RELAY)
  1. Inspect the ST relay (Click here).



NG
REPLACE RELAY (ST RELAY)
OK


4.INSPECT STARTER ASSEMBLY
  1. Inspect the starter assembly (Click here for 1.6 kW Type, Click here for 1.7 kW Type).

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 1.6 kW Type)
    B
    NG (for 1.7 kW Type)
    C



B
REPLACE STARTER ASSEMBLY (for 1.6 kW Type) (Click here)

C
REPLACE STARTER ASSEMBLY (for 1.7 kW Type) (Click here)
A


5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the starter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 3 - E9-1
    Always
    Below 1 Ω
    ST relay terminal 3 or E9-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the cable from the positive (+) battery terminal.

  1. Disconnect the starter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Positive (+) battery terminal - F2-1
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 1 - Body ground
    Always
    Below 1 Ω


    Result 
    Result
    Proceed to
    OK (w/o smart entry and start system)
    A
    OK (w/ smart entry and start system or Push-Button Start)
    B
    NG
    C



B
Go to step 11

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E85-9 (L) - ST relay terminal 2
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - ST RELAY)
  1. Disconnect the ignition switch assembly connector.

  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    I36-7 (ST2) - ST relay terminal 5
    Always
    Below 1 Ω
    I36-7 (ST2) or ST relay terminal 5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY) 

11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ST RELAY)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E85-9 (L) - ST relay terminal 2
    Always
    Below 1 Ω
    A25-22 (STA) - ST relay terminal 2
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST RELAY) 

12.READ VALUE USING GTS (STARTER SIGNAL)
  1. Connect the GTS to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

  1. Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

    OK 
    Ignition Switch Position
    Starter Signal
    ON
    OFF
    START
    ON



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

13.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).

    Result 
    Result
    Proceed to
    OK (w/o smart entry and start system)
    A
    OK (w/ smart entry and start system or Push-Button Start)
    B
    NG
    C



B
Go to step 17

C
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
A


14.INSPECT IGNITION SWITCH ASSEMBLY
  1. Inspect the ignition switch assembly (Click here).



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


15.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ignition switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    I36-3 (ST1) - E85-4
    Always
    Below 1 Ω
    I36-3 (ST1) - E26-63 (NSW)
    Always
    Below 1 Ω
    I36-3 (ST1) or E85-4 or E26-63 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY - ECM)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 2 - E85-9 (L)
    Always
    Below 1 Ω
    ST relay terminal 2 or E85-9 (L) or A25-22 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY) 

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    A43-5 (STAR) - E85-4
    Always
    Below 1 Ω
    A43-5 (STAR) - E26-63 (NSW)
    Always
    Below 1 Ω
    A43-5 (STAR) or E85-4 or E26-63 (NSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY - ECM - CERTIFICATION ECU)
  1. Remove the ST relay from the engine room relay block and junction block assembly.

  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the ECM connector.

  1. Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 2 - E85-9 (L)
    Always
    Below 1 Ω
    ST relay terminal 2 or E85-9 (L) or A25-22 (STA) or A43-7 (STA) - Body ground
    Always
    10 kΩ or higher


Result 
Result
Proceed to
OK (Smart Entry And Start System)
A
OK (Push-Button Start)
B
NG
C


B
GO TO PUSH-BUTTON START (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

GO TO SMART ENTRY AND START SYSTEM (Click here)