Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

AIR CONDITIONING SYSTEM > PTC Heater Circuit

for Preparation Click here


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.

Quick Heater Assembly (PTC Heater) Operation Condition 
Control ECU
Condition
Air Conditioning Amplifier Assembly
Engine running
Blower switch: On
Temperature settings: MAX HOT
Light control switch off
  1. Engine coolant temperature 70°C (158°F) or lower (2 PTC heater relays operating)
  2. Engine coolant temperature 75°C (167°F) or lower (1 PTC heater relay operating)
Ambient temperature 10°C (50°F) or lower

WIRING DIAGRAM


E240747E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.


Air Conditioner 
Tester Display
Test Part
Control Range
Diagnostic Note
Heater Active Level
Quick heater assembly
Min.: 0, Max.: 2
-

OK:
Heater Active Level changes normally.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK


2.INSPECT PTC HEATER RELAY (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY)


    E287491E02
  1. Remove the PTC HTR NO. 1 relay and PTC HTR NO. 2 relay.
    Text in illustration 
    *a
    Component without harness connected
    (PTC Heater Relay)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE PTC HEATER RELAY
OK


3.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - POWER SOURCE)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    PTC HTR NO. 1 
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 3 - Body ground
    Always
    11 to 14 V
    Relay terminal 2 - Body ground
    Ignition switch off
    Below 1 V
    Relay terminal 2 - Body ground
    Ignition switch ON
    11 to 14 V

    Standard Voltage:
    PTC HTR NO. 2 
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 3 - Body ground
    Always
    11 to 14 V
    Relay terminal 2 - Body ground
    Ignition switch off
    Below 1 V
    Relay terminal 2 - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    PTC HTR NO. 1 
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 1 - I77-15 (PTC1)
    Always
    Below 1 Ω
    Relay terminal 1 - Body ground
    Always
    10 kΩ or higher

    Standard Resistance:
    PTC HTR NO. 2 
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 1 - I77-16 (PTC2)
    Always
    Below 1 Ω
    Relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (PTC HTR NO. 1 RELAY, PTC HTR NO. 2 RELAY - QUICK HEATER ASSEMBLY AND BODY GROUND)
  1. Disconnect the I202 quick heater assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    PTC HTR NO. 1 
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 5 - I202-1 (B)
    Always
    Below 1 Ω
    I202-1 (B) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance:
    PTC HTR NO. 2 
    Tester Connection
    Condition
    Specified Condition
    Relay terminal 5 - I202-2 (B)
    Always
    Below 1 Ω
    I202-2 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT QUICK HEATER ASSEMBLY
  1. Remove the quick heater assembly (Click here).



    E230975E14
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I202-1 (B) - a1-1 (E)
    Always
    Below 1 Ω
    I202-2 (B) - a1-1 (E)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Quick Heater Assembly)



NG
REPLACE QUICK HEATER ASSEMBLY (Click here)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)