Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR

BRAKE ACTUATOR > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE ACTUATOR ASSEMBLY


    C236074E01
  1. Install the brake actuator assembly to the brake actuator bracket assembly.

    NOTICE:
    1. Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.
    2. Do not hold the brake actuator assembly by the connector.

  1. Tighten the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    Tighten the 3 nuts in the order shown in the illustration.



2. INSTALL BRAKE ACTUATOR WITH BRACKET


    C239183E01
  1. Install the brake actuator with bracket to the vehicle body with the 3 bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    1. Do not damage the brake lines, suction hose sub-assembly or wire harness.
    2. Tighten the 3 bolts in the order shown in the illustration.



    C239182E01
  1. Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.
    Text in Illustration 
    *a
    From 1st Chamber of Master Cylinder Sub-assembly
    *b
    From 2nd Chamber of Master Cylinder Sub-assembly
    *c
    To Front Wheel Cylinder Assembly LH
    *d
    To Rear Wheel Cylinder Assembly RH
    *e
    To Rear Wheel Cylinder Assembly LH
    *f
    To Front Wheel Cylinder Assembly RH



    C311087E01
  1. Using a union nut wrench, fully tighten each brake line.
    Text in Illustration 
    *a
    Torque Wrench Fulcrum Length

    Torque:
    Specified tightening torque (a):
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    Specified tightening torque (b):
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    HINT:
    1. Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).
    2. When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):
      (a): 14 N*m (142 kgf*cm, 10 ft.*lbf)
    3. When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):
      (b): 18 N*m (184 kgf*cm, 13 ft.*lbf)



    C239181E01
  1. Connect the brake actuator connector and disengage the claw (b).

  1. Put the lever down and engage the claw (a) to engage the connector lock.

    NOTICE:
    1. Make sure that the connector is locked securely.
    2. Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter.



3. INSTALL SUCTION PIPE CLAMP
  1. Engage the suction pipe clamp to install it to the brake actuator bracket assembly.



4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



5. BLEED BRAKE SYSTEM
(Click here)


6. INSPECT BRAKE ACTUATOR USING INTELLIGENT TESTER
(Click here)


7. PERFORM SYSTEM VARIANT LEARNING
(Click here)


8. CHECK FOR AND CLEAR DTCS
(Click here)