PARKING ASSIST MONITOR SYSTEM > CALIBRATION |
| ADJUST PARKING ASSIST MONITOR SYSTEM |
The parking assist monitor system can be adjusted using diagnostic mode.
If the following operations are performed, it is necessary to perform adjustments and checks using diagnostic mode.
| Part Name | Operation | Adjustment Item | Proceed to |
| Steering Sensor |
| Steering angle neutral point (Initialize parking assist monitor system) |
Click here
|
| Steering angle setting | Procedure 3 | ||
| Suspension, tires, etc. | Replacement (The vehicle height changes due to suspension or tire replacement) | Rear television camera assembly optical axis (Back camera position setting) | Procedure 2 |
| Rear television camera assembly | Replacement | Parking assist monitor system initialization | Procedure 1 |
| Removal and installation of the rear television camera assembly etc. (Installation angle of the rear television camera assembly changes due to the removal and installation) | Rear television camera assembly optical axis (Back camera position setting) | Procedure 2 |
| PARKING ASSIST MONITOR SYSTEM INITIALIZATION (PROCEDURE 1) |
Preparation for adjustment
Park the vehicle with the steering wheel centered.
![]() |
Set a target bar behind the vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).
| Area | Specification |
| A | 821 to 831 mm (2.692 to 2.725 ft.) |
| B | 1995 to 2005 mm (6.544 to 6.576 ft.) |
| *a | Vehicle Center |
| *b | Target Bar for Back Camera Position Setting |
| *c | Vehicle End |
| *d | Front |
Start diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" on the "Service Menu" screen.
![]() |
Select "Camera Setting" on the "Function Check/Setting I" screen.
![]() |
Select "Next" on the "Car Signal Check" screen.
Steering Angle Setting
![]() |
Check that the steering wheel is centered (approximately +/- 5 degrees or less) and then select "STEERING CENTER MEMORIZE".
After performing the steering center memorize operation, turn the steering wheel to the left and right lock positions and select "MAX STEERING ANGLE MEMORIZE". The maximum steering angle is then stored and the screen changes to the "Back Camera Position Setting" screen.
![]() |
Back Camera Position Setting
| *a | Target Bar for Back Camera Position Setting |
Perform vertical and horizontal position adjustment.
Perform roll angle adjustment.
Select "Next" on the "Back Camera Position Setting" screen.
![]() |
Back Verify Mode
Check that (A) and the target adjustment bar are overlapping.
Select "OK" to return to the "Function Check/ Setting I" screen and complete the adjustment.
Finish diagnostic mode (Click here).
Confirm steering angle adjustment.
Check on the parking assist screen that the estimated course line moves until the steering wheel is fully turned to either the left or right.
| BACK CAMERA POSITION SETTING (PROCEDURE 2) |
Preparation for adjustment
Park the vehicle with the steering wheel centered.
![]() |
Set a target bar behind the vehicle for optical axis adjustment of the rear television camera assembly (back camera position setting).
| Area | Specification |
| A | 821 to 831 mm (2.692 to 2.725 ft.) |
| B | 1995 to 2005 mm (6.544 to 6.576 ft.) |
| *a | Vehicle Center |
| *b | Target Bar for Back Camera Position Setting |
| *c | Vehicle End |
| *d | Front |
Start diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" on the "Service Menu" screen.
![]() |
Select "Camera Setting" on the "Function Check/Setting I" screen.
![]() |
Select "Back Camera Setting" on the "Mode Setting" screen.
![]() |
Select "Next" on the "Car Signal Check" screen.
![]() |
Back Camera Position Setting
| *a | Target Bar for Back Camera Position Setting |
Perform vertical and horizontal position adjustment.
Perform roll angle adjustment.
Select "Next" on the "Back Camera Position Setting" screen.
![]() |
Back Verify Mode
Check that (A) and the target adjustment bar are overlapping.
Select "OK" to return to the "Mode Setting" screen and complete the adjustment.
Finish diagnostic mode (Click here).
| STEERING ANGLE SETTING (PROCEDURE 3) |
Center the steering wheel and stop the vehicle.
Start diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" on the "Service Menu" screen.
![]() |
Select "Camera Setting" on the "Function Check/Setting I" screen.
![]() |
Select "Steering Angle Setting" on the "Mode Setting" screen.
![]() |
Select "Next" on the "Car Signal Check" screen to display the "Steering Angle Setting" screen.
![]() |
Steering Angle Setting
Check that the steering wheel is centered (approximately +/- 5 degrees or less) and select "STEERING CENTER MEMORIZE".
After the centered steering position is memorized, turn the steering wheel to the left and then to the right full lock positions and select "MAX STEERING ANGLE MEMORIZE".
Select "MAX STEERING ANGLE MEMORIZE" to store the steering angle adjustment value and change the screen to the "Mode Setting" screen.
Finish diagnostic mode (Click here).
Confirm steering angle adjustment.
Check on the parking assist screen that the estimated course line moves until the steering wheel is fully turned to either the left or right.