Home › Engine / Hybrid System ยท 2GR-FE › ENGINE CONTROL › SFI SYSTEM

DTC    P0017    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)

DTC    P0019    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)

for Preparation Click here


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate exhaust valve open and close timing is controlled by the ECM. The ECM performs exhaust valve control by performing the following: 1) controlling the exhaust camshaft and camshaft timing oil control valve assembly (for exhaust camshaft), and operating the camshaft timing exhaust gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No.
DTC Detection Condition
Trouble Area
P0017
Deviation in the crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 1) signal (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for exhaust camshaft of bank 1, 2)
  3. Oil control valve filter (RH, LH)
  4. Oil pipe
  5. Camshaft timing exhaust gear assembly (bank 1, 2)
  6. ECM
P0019
Deviation in the crankshaft position sensor signal and VVT sensor (for exhaust camshaft of bank 2) signal (2 trip detection logic).

MONITOR DESCRIPTION

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM stores DTC P0017 (bank 1) or P0019 (bank 2).

MONITOR STRATEGY


Required Sensors/Components (Main)
Camshaft timing exhaust gear assembly
Required Sensors/Components (Related)
VVT sensor
Crankshaft position sensor
Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Engine speed
500 to 1000 rpm

CONFIRMATION DRIVING PATTERN


A197314E03

  1. Connect the intelligent tester to the DLC3.
  2. Turn the engine switch on (IG) and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the tester on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].
  8. Enter the following menus: Powertrain / Engine / DTC [D].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P0017 or P0019.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].

  13. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Idle the engine for 5 minutes or more [F].
  15. Enter the following menus: Powertrain / Engine / DTC [G].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Check the DTC judgment result.

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.


INSPECTION PROCEDURE

HINT:
  1. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transaxle.
  2. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  3. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0017 OR P0019)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P0017 or P0019 is output
    A
    DTC P0017 or P0019 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0017 or P0019 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the A/C switch on.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2) / All Data / VVT Ex Chg Angle #1 or VVT Ex Chg Angle #2.

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Displacement angle varies.



NG
Go to step 4
OK


3.ADJUST VALVE TIMING
  1. Adjust the valve timing (Click here).



NEXT
Go to step 7

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
  1. Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) (Click here)
OK


5.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE


    A210289E03
  1. Remove the oil pipe or No. 1 oil pipe (Click here).

  1. Remove the oil control valve filter RH or oil control valve filter LH.

  1. Check that the oil control valve filter and oil pipe are not clogged.

    OK:
    The oil control valve filter or oil pipe is not clogged.

    Text in Illustration 
    *1
    Bank 1
    *2
    Bank 2
    *a
    Oil Pipe
    *b
    No. 1 Oil Pipe



NG
REPLACE OIL CONTROL VALVE FILTER OR OIL PIPE (Click here)
OK


6.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Inspect the camshaft timing exhaust gear assembly .

    HINT:
    Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly (Click here).



NG
REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (Click here)
OK


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / DTC / Pending.

  1. Read the pending DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0017 or P0019 is output
    B



B
REPLACE ECM (Click here)
A

END