REAR DOOR COURTESY SWITCH (for TMC, TMMR Made) > REMOVAL |
| 1. PRECAUTION (w/ Rear Seat Side Airbag) |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag) |
| 3. REMOVE REAR SEAT HEADREST ASSEMBLY (for Fold Down Seat Type) |
| 4. REMOVE REAR SEATBACK ASSEMBLY (for Fold Down Seat Type) |
Disconnect the rear seat outer belt assembly from the rear seat center shoulder belt guide.
Fold down the rear seatback assembly LH.
![]() |
Disengage the fastener as shown in the illustration.
| *1 | Fastener |
w/o Seat Heater System:
![]() |
Remove the 2 bolts and rear seatback assembly LH.
w/ Seat Heater System:
![]() |
Remove the 2 bolts and disconnect the rear seatback assembly LH.
![]() |
Disconnect the connector.
Disengage the clamp and remove the rear seatback assembly LH.
| 5. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type) |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
w/ Seat Heater System:
Disconnect the connector.
![]() |
Disengage the 2 clamps.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 6. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type) |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 7. REMOVE REAR SIDE SEATBACK ASSEMBLY (for Fold Down Seat Type) |
Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide LH.
![]() |
Remove the bolt.
Disengage the hook and remove the rear side seatback assembly LH.
| 8. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type) |
| 9. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type) |
![]() |
Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.
| a | 100 mm (3.94 in.) or less |
Disconnect the 2 seat heater connectors.
Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.
| 10. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type) |
![]() |
Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.
| 11. REMOVE REAR SEATBACK COVER (for Reclining Seat Type) |
![]() |
Disengage the 4 claws and remove the 2 rear seatback covers.
| 12. REMOVE REAR SEATBACK ASSEMBLY (for Reclining Seat Type) |
w/ Rear Seat Side Airbag:
Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.
Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.
![]() |
Disengage the 2 hooks and disconnect the cover.
Remove the 2 nuts, 2 bolts and rear seatback assembly LH.
| 13. REMOVE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY |
Disconnect the connector.
![]() |
Using a T30 "TORX" socket wrench, remove the screw and rear door courtesy light switch assembly.